Steinbach 012610 Bedienungsanleitung Seite 8

EN
The necessary electrical connections must be made by a licensed
electrical contractor. The supply lines are secure and in addition to
earth with a residual current circuit breaker 30 milliamps. The rele-
vant statutory provisions as ÖVE, VDE etc. must be observed.
Avoid sharp objects in the pool. This could lead to damage to the
film. Do not climb onto the handrail. This could result in damage to
the handrail or the pelvic wall.
Swimming pools with a depth of 120 or 132 cm are not suitable for
dives or headjumps. Failure to comply could result in severe head or
spinal injuries!
Never leave your children unattended when they are in or around the
swimming pool!
Should there be children in your home or neighborhood, who can not
swim, we recommend you to set up an inexpensive mesh fence
which is available in construction stores, around your pool.
Tarpaulins or other pool covers do not provide child safety. So do
not leave that pool covers, no matter what kind they are, get rid of
the responsibility for your children.
Location of your pool (Figure 1)
When choosing a location for your
tion of several factors.
Under no circumstances, the swimming pool must be installed below
ground level. This swimming pool must only be installed above
ground and on a hard, solid ground.
be bolted on banked surfaces.
thus damage to the swimming
niest spot in your garden. The larger the area of the
it is. At least you should have an open space of about 90 cm around
the pool.
If there is the possibility of a sheltered
for your pool. A swimming pool which is unprotected from the wind is
subject to a high heat loss by convection and
shouldn't place your pool next to or
maintenance effort).
Under no circumstances your pool should be installed under
overhead lines. Avoid providing your pool on land lines.
Location of the filter system
Your pool should be equipped with a sand filter. In free-standing filter
systems is a minimum distance from the edge of the pool to be
observed. For further information please see the attached
description of the filter system.
Preparing an installation site
We want you to have your pool for many years with great pleasure.
The effort and care that you put into the preparation of the
foundations can make a great difference in the life span of your
swimming pool and its liner. The better prepared and fixed the place
is, the longer you will have to enjoy your swimming pool. Therfore
we apply appropriate care. It is absolutely necessary that the ground
on which your pool is built is flat and stable (no banked areas).
Settlements would inevitably lead to deformity and damage to your
pool. Remove roots, grass and stones in the selected area, including
those under the ground. The weight of the water will compress these
elements between the liner and the earth under the swimming pool,
resulting in damages. Grass left underneath the pool liner will rot and
give of an unpleasant odor and stones and roots will damage the
pool liner.
If you build your pool directly on concrete, asphalt or a similar
surface, so it is essential that between the substrate and the film a
commercial mineral fiber fabric is introduced as a separating layer.
Never install this swimming pool inside a garage, or on a balcony,
roof, terrace or any other surface that is not completely flat and solid.
Page 8 of 50
pool, you should take considera-
Your pool should therefore not
This could lead to subsidence and
pool. If it is possible choose the sun-
basin, the better
spot, so you should choose
evaporation.
under trees, bushes, etc.
The maximum weight that the installation site can support must be
taken into consideration.
The basin is generally not suitable for installation in the ground,
there is no guarantee at contravene.
Plot the place of installation
Please refer to the dimensions according to the table and draw on
your installation location with lime powder or spray paint.
3. Hammer a peg into the ground in the center of the area where
you want your pool.
4. Now drag a circle with a cord and a can of paint or spray with lime
powder, with the radius of which is specified in the table.
Tank size
Ø 3,5 m
Ø 4,6 m
Ø 5,5 m
R+ is the radius of the required footprint. (Figure 2,4)
3. Level the ground in the marked area. The entire area of the
swimming pool must be leveled and free of stones and twigs.
(Figure 5)
Leveling the place of installation
Using a leveling tool, a straight wooden board or even better would
be a yardstick (alu slat) and level the surface down to the level of the
lowest point. Do not fill in the holes; dig away higher areas. Scatter a
fine layer of sifted sand over the levelled surface and level again. Dig
from the raised
You
lead to subsidence.
(large
Figure 6, 7
Now pave the installation location so until this is completely flat. Only
a properly prepared installation site is a prerequisite for a functional
pool.
Using floor insulation:
If you isolate the pelvic floor with Styrofoam or Styrodur, it is
necessary to make the whole pool to the insulation.
Bring to a maximum of 3 cm thick, flat gravel layer and compress
them. Then place the insulation into the bottom gravel bed.
Figure 9
7) Floor insulation treadable
8) Gravel bed max. 3 cm
9) Excavation turf
Figure 10
10) Excavation
11) gravel bed
12) floor insulation added sheepishly
With a concrete foundation the instructions are the same, with the
concrete slab replaced the gravel bed (thickness depends on the
local conditions at 15 - 20 cm with steel reinforcement).
Underground Installation
In-ground installation of the pool, you must provide a suitable
pressure protection around the basin. This can be made of
lightweight concrete, lean concrete or by building a peripheral wall.
Why? The pressure of the back-filling with earth or gravel is a
multiple of the water pressure. If no backfill to stabilize with light or
lean is done, the pool may collapse during emptying.
R R+ detached
1,75 m 2,0 m
2,30 m 2,55 m
2,75 m 3,0 m
spots. In no case the subscript throw
Highline rund | 2016_V1
R+ sunk
2,25 m
2,80 m
3,25 m
up, this could