Kärcher NT 30/1 Ap L Bedienungsanleitung Seite 17

Installing the squeegees
1. Remove the brush strip.Illustration E
2. Install the squeegees.
Note
The structured side of the squeegees must face outwards.
Removing the fleece filter bag
⚫ The fleece filter bag must always be removed when
vacuuming wet substances.
1. Unlock and remove the suction head.
2. Pull the fleece filter bag on the flange up and
out.Illustration F
3. Seal the fleece filter bag with cap.
4. Dispose of the used fleece filter bag in accordance with
statutory regulations.
5. Fit and lock the suction head.
Removing the dust bag
⚫ The dust bag (special accessories) must always be
removed when vacuuming wet substances.
1. Unlock and remove the suction head.
2. Fold up the dust bag (special accessories). Illustration
G
3. Take off the protective film and close the ventilation hole
with a self-adhesive tab.
4. Close the dust bag (special accessory) tightly with a
cable tie underneath the opening.
5. Take out the dust bag (special accessories).
6. Clean the container inside with a moist cloth.
7. Dispose of the dust bag (special accessory) in
accordance with statutory provisions.
8. Fit and lock the suction head.
Draining the waste water NT
50/1 only:
1. Drain the waste water via the drain hose. Illustration H
General
⚫ We recommend not using the "Semi-automatic filter
dedusting" function button when vacuuming wet dirt with
the crevice nozzle or upholstery nozzle (optional) when
sucking mainly water out of a container.
⚫ The device switches off automatically when the
maximum fluid level is reached.
⚫ When vacuuming non-conductive liquids (e.g. drill
emulsion, oils and grease) the device does not
automatically switch off when the container is full. The
filling level must be continuously monitored and the
container emptied on a timely basis.
⚫ On completion of wet vacuum cleaning: Clean the main
filter element using the filter cleaning. Clean the
electrodes with a brush. Clean the container with a
moist cloth and dry it off.
Clip connection
The suction hose is equipped with a clip system. All
accessory parts with a nominal width of 35 mm can be
connected.
Illustration I
Switching on the device
1. Connect the mains plug.
2. Switch on the device at the turn switch.
Working with power tools
Only for devices with a built-in socket:
DANGER
Danger of electric
shock Risk of injury and
damage.
The socket is only intended for direct connection of
power tools to the vacuum cleaner. Any other use
of the socket is prohibited.
1. Plug the mains plug of the power tool into the
power socket on the vacuum cleaner. The
vacuum cleaner is in Standby mode.
2. Switch on the device at the turn switch.
Note
The vacuum cleaner is automatically switched on
and off with the power tool.
Note
The vacuum cleaner has a startup delay of up to
0.5 seconds and an after-running time of up to 15
seconds.
Note
See the Technical data for the permissible power
rating of the power tool.
3. Remove the angle piece from the suction
hose.Illustration J
4. Install the tool adapter on the suction hose.
5. Connect the tool adapter to the power tool.
Illustration K
Semi-automatic filter dedusting
Note
Actuating the filter dedusting every 5-10 minutes
extends the working time of the main filter
element.
Note
The semi-automatic filter dedusting can only be
switched on when the device is switched on. 1.
Press the semi-automatic filter dedusting button
5x. The main filter element is then cleaned by a
blast of air (pulsing sound).
2. Power dedusting (for particularly severe
contamination of the main filter element):
Close off the suction pipe or angle piece with
your hand and press the semi-automatic filter
dedusting button 5x with the device switched
on.
Illustration L
Switching off the device
1. Press the semi-automatic filter dedusting
button 5x.
2. Switch off the device at the turn switch.
3. Pull out the mains plug.
English
Operation
17