Hart® Menübaum - Emerson Rosemount 848T Wireless Betriebsanleitung

Rosemount 848T Wireless
® Menübaum
HART
Abbildung 2-3. Handterminal Menübaum
1. Overview
1. Guided Setup
2. Configure
2. Manual Setup
3. Service Tools 3. Alert Setup
1. Active Alerts
2. Communication
Status
3. Sensor 1
4. Sensor 1 Status
5. Sensor 2
6. Sensor 2 Status
7. Sensor 3
8. Sensor 3 Status
9. Sensor 4
10. Sensor 4 Status
11. Last Update Time
1. Device Alerts
2. Variables
3. Communications
4. Routine Maintenance
5. Simulate
2-8
Fett gedruckte Optionen weisen darauf hin, dass weitere Auswahlmöglichkeiten
verfügbar sind. Kalibrier- und Einstellungsdaten wie Sensortyp, Anzahl der
Leiter und Messbereichswerte können an mehreren Stellen geändert werden,
um die Bedienung zu vereinfachen.
1. Network ID
1. Join Device to Network
2. Join Device to Network
2. Configure Update Rate
3. Update Rate
3. Configure Sensors
4. Configure Broadcast Power Level
4. Calibrate Sensors
5. Power Mode
5. Configure Alerts
6. Power Source
1. Sensor X
1. Wireless
2. Status
2. Sensor 1
3. Configure Sensor
3. Sensor 2
4. Unit
4. Sensor 3
5. Type
5. Sensor 4
6. Connection
6. Device Temperature
7. Serial Number
7. Device Information
8. Maximum
8. Other
9. Minimum
1. Electronics Temperature
2. Status
3. Unit
4. Maximum
5. Minimum
1. Tag
2. Long Tag
3. Device
4. Sensor
5. Wireless
1. Write Protect
2. AC Power Filter
3. Measurement and Status Log
4. Accuracy Mode
5. Master Reset
6. Advertise to New Devices
1. Sensor 1 Process Alert
2. Sensor 2 Process Alert 1. High Alert
3. Sensor 3 Process Alert 2. Low Alert
4. Sensor 4 Process Alert
1. Active
1. Clear Alert History
2. History
Display a list of historical alerts
1. Sensor 1
2. Sensor 1 Status
3. Sensor 2
4. Sensor 2 Status
5. Sensor 3
1. Join Status
6. Sensor 3 Status
2. Communication Status
7. Sensor 4
3. Join Mode
8. Sensor 4 Status
4. Number of Advertisements Heard
9. Electroncs Temperature
5. Number of Avaliable Neighbors
10. Electronics Temperature Status
6. Number of Join Attempts
11. Supply Voltage
12. Supply Voltage Status
13. Last Update Time
1. Calibrate Sensor 1
2. Calibrate Sensor 2
1. Sensor X
3. Calibrate Sensor 3
2. Status
4. Calibrate Sensor 4
3. Current Upper Trim
5. Other
4. Current Lower Trim
5. Lower Sensor Trim
6. Upper Sensor Trim
7. Recall Factory Trim
8. RTD 2-wire offset
1. Process Sensors
2. Electronics Temperature
3. Supply Voltage
1. Perform Master Reset
2. Measurement History
3. Advertise to New Devices
Betriebsanleitung
00809-0105-4848, Rev AA
1. Configure Update rate
2. Message 1
3. Message 2
4. Message 3
1. Manufacturer
2. Model
3. Final Assembly Number
4. Universal Rev
5. Field Device Rev
6. Software Rev
7. Hardware Rev
8. Descriptor
9. Message
10. Date
11. Model Number
12. SI Unit Control
13. Country
14. Device ID
1. Sensor 1 S/N
2. Sensor 2 S/N
3. Sensor 3 S/N
4. Sensor 4 S/N
1. Manufacturer
2. Device Type
3. Device Revision
4. Software Revision
5. Hardware Revision
1. Mode
2. Trigger Point
3. Dead Band
Juli 2009
1. Message
2. Update Rate