Safety Instructions - Ferm BSM1002 Gebrauchsanweisung

SPARE PARTS LIST FBS-1000
REF NR DESCRIPTION
007 BALL BEARING 629 Z
009 ROTOR
011 STATOR
013 CARBON BRUSH CAP
014 CARBON BRUSH SET
015 CARBON BRUSH HOLDER
019 SMALL BAND WHEEL
020 V-BELT
022 SPINDLE
023 IDLE WHEEL
030 NEEDLE BEARING HK081210
036 SWITCH
044 RUBBER FOR DRIVE WHEEL
045 DRIVE WHEEL
046 BALL BEARING 6800 ZZ
050 + 051 ADJUSTING KNOB + SPRING
053 BIG BAND WHEEL
055 BALL BEARING 627 ZZ
064 BALL BEARING 609 ZZ
- DUSTBAG COMPLETE
30
FERM NR
800629
BELT SANDER
409200
409201
TECHNICAL SPECIFICATIONS
409202
409203
Voltage
Frequency
409204
Power input
409205
No load sander paper speed
Sanding belt size
409206
Sanding pad size
409207
Weight
409208
Lpa (Sound pressure)
Lwa (Sound power level)
801211
Vibration value
302008
409209
PRODUCTINFORMATION
409210
Fig. A
The belt sander is the perfect tool to sand wood and to
806800
grind iron, plastic or similar materials.
409211
The belt sander must be used for the rough work, for the
409212
normal sanding work an orbital sander must be used.
800627
1. On/off switch
800609
2. Front handle
409213 3. Rear handle
4. Blocking switch
5. Dust collection opening
6 Adjusting knob
7. Sanding belt fastener
8. Front belt roller
9. Direction indicator
10. Drive belt cover
11. Dust bag
PACKAGE CONTENTS
1 Belt sander
3 Sanding belts
1 Dust collection bag
1 Instruction manual

1 Safety instructions

1 Guarantee card
Check the machine, loose parts and accessories for
transport damage.
Ferm Ferm
SAFETY INSTRUCTIONS
The following pictograms are used in these instructions
for use:
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
| 230 V~
| 50 Hz
| 1000 W
Carefully read this manual before using the machine.
| 320 m/min
Make sure that you know how the machine functions and
| 100 x 533 mm
how to operate it. Maintain the machine in accordance
| 100 x 135 mm
with the instructions to make sure it functions properly.
| 4.8 kg
Keep this manual and the enclosed documentation with
| 93.5 dB(A)
the machine.
| 106.5 dB(A)
| 4.729 m/s
2
ELECTRICAL SAFETY
Always check that the power supply corresponds
with the voltage on the rating plate.
The machine is double insulated in accordance
with EN-50144; therefore no earth wire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm 2 . When using a cable reel always unwind
the reel completely.
SPECIAL SAFETY PRECAUTIONS
• If you are working with the sanding machine, wear
always ear protectors and dust mask.
• The sanding machine is not suitable for wet sanding.
• Check if the switch is not in position "ON", before
you connect the mains plug to the mains voltage.
• Keep the mains lead always away from moving parts
of the tools.
• Use safety glasses, especially when you sand above
your head.
• Do not bring pressure to your machine, this will only
delay the sanding.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or mains
lead damage.
• Defect switch
• Smoke or stench of scorched isolation
3