Start-Up And Settings - Loewe Compact Bedienungsanleitung

Start-up and settings

Before commencing the start-up and settings, please make sure that all cables
are connected correctly.
Switching the subwoofer on/off
Use the mains switch Power to switch the subwoofer on in position ON
5
and off in position OFF.
➠
If you wish to toggle between the operating modes Wireless or Cable via
Audio-Link, switch the unit off for minimum 30 seconds and then on again.
Mode with Loewe TV sets
If the subwoofer is connected via the Audio-Link connection, as described on
page 13, the Mode - ON/AUTO
2
the Mode - 2.1/Stereo switch is on the 2.1 position, you no longer need
6
to switch the subwoofer on and off separately. After switching on the subwoofer
for the rst time, it is automatically switched on and off together with the
Loewe TV set.
➠
Register the presence of the subwoofer as described in the instructions for
use of your Loewe TV set under "Operating extra devices" or "External
devices".
Automatic operation with other audio sources
If there is no Audio-Link connection, the Mode - ON/AUTO
the AUTO position and if audio signals are present at the Cinch sockets Line
IN - Right/Subw/Left the subwoofer will switch on automatically. After 10
1
minutes without an audio signal at these sockets, the subwoofer will switch off
automatically.
➠
The subwoofer can switch on automatically if fault signals are present on
the audio lines. In this case, activate the mains switch
➠
The subwoofer can switch off automatically during longer, very quiet pas-
sages. In this case, increase the volume.
Continuous operation with other audio sources
If you wish to operate the subwoofer in continuous mode, switch the Mode -
ON/AUTO switch to the ON position. Then switch the subwoofer on or off
7
with the mains switch Power .
5
Stereo mode
Move the Mode - 2.1/Stereo switch
are only feeding the audio signals in at the Cinch sockets Line IN - Right/Left.
The bass manager integrated in the subwoofer then automatically directs
1
the bass components contained in the stereo signals to the subwoofer channel.
- 14
switch is in the AUTO position and
7
switch is at
7
.
5
switch to the Stereo position if you
6
2.1 Mode
Move the Mode - 2.1/Stereo switch
the audio signals in at the Cinch sockets Line IN - Right/Subw/Left
Wireless
Move the Mode - ON/AUTO switch to the ON position if you wish to
7
connect the subwoofer to a compatible audio source via a wireless link. Activate
Coupling mode, as described in the instruction manual of the relevant audio
source. Use a sharp object (e.g. paper clip) and press brie y on the button in the
opening to move the optional Module Wireless Audio Link in Coupling
8
mode. If the registration was not successful, please try again and reduce the
distance of the subwoofer to the audio source.
➠
The distance between the subwoofer and audio source must not exceed 10
m in the same room.
➠
The rotary switches Crossover Frequency
Intensity do not have any function in the Wireless operating mode.
11
Setting the crossover frequency
The Crossover Frequency knob
9
frequency for the bass playback - depending on which speakers you have con-
nected - between 50 Hz and 350 Hz.
As described on page 13, for Loewe audio systems the knob should be set
to 350 Hz because the crossover frequency is set to this in the Loewe audio
sources (TV set).
Setting the equalizer
The Equalizer knob gives you the option of setting a reduction or increase
10
in the lowest frequency ranges (20 Hz - 50 Hz) for the bass playback.
• If the subwoofer is near the corner of the room, turn the Equalizer knob
more towards -3 dB.
• If the subwoofer is near a wall, then turn the Equalizer knob more to the
middle position.
• If the subwoofer is freestanding in the room, turn the Equalizer knob
more towards +3 dB.
Bass intensity
You can use the Bass Intensity control
you want it.
switch to the 2.1 if you are feeding
6
1 .
, Equalizer and Bass
9 10
gives you the option to set the limit
to set the basic bass volume to how
11
10
10