EINHELL TE-MB 18/127 Li Originalbetriebsanleitung Seite 21

push the workpiece stop (13) to the required
position. Then retighten the two socket head
screws (14).
5.4 Information about the LED lamp (Fig. 1)
•
The machine has an LED lamp (4) for illumi-
nating the cutting area.
•
As soon as you press the On/Off switch (3),
the LED lamp (4) will come on automatically.
•
A few seconds after you release the On/Off
switch (3) again, the LED lamp (4) will switch
off automatically.
5.5 Fitting/removing the blade (Fig. 5 – 7)
•
Before you change the blade: Remove the
battery!
•
Wear work gloves to prevent injury when
changing the blade.
•
Slacken the blade (15) by turning the clam-
ping lever (16) clockwise.
•
To remove the blade: start at the top part of
the blade guard (17), then continue around
the blade pulleys (18) and finish at the guide
rollers (20).
•
Caution! When the blade is being removed,
the tension might be released with a jerk
causing the blade (15) to jump off the blade
pulleys (18)!
•
Before you mount the new blade, clean the
guide rollers (20) and the two blade pulleys
(18). Make sure in particular that the rubber
tire (19) is free of chips.
•
Caution! A damaged rubber tire (19) must be
replaced immediately.
•
Mount the new blade (15) in reverse order
beginning at the guide rollers (20).
•
Caution! Pay attention to the running direc-
tion. The cutting angle of the teeth must point
in running direction, i.e. towards the workpie-
ce stop (13). (See the arrow on the two blade
pulleys (18)).
•
Make sure that the new blade (15) runs freely
in the guide rollers (20) and in the upper bla-
de guard (17).
•
Tension the blade (15) by turning the clam-
ping lever (16) counter-clockwise.
•
Important! The blade must first be run in.
Switch on the machine briefly and check how
the blade is running. Check that the blade is
running correctly before you start cutting.
•
Important! The width of the new blade must
be at least as large as stipulated in section
4. Technical data. The teeth of the blade (15)
must project beyond the guide rollers (20)
(see Fig. 7b). If the new blade (15) is too nar-
Anl_TE_MB_18_127_Li_SPK13.indb 21 Anl_TE_MB_18_127_Li_SPK13.indb 21
GB
row, the teeth will be damaged and the blade
will become blunt.
6. Operation
6.1 Charging the Li battery pack (Fig. 8/9)
1. Remove the battery pack (6) from the handle,
pressing the pushlock button (8) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(7) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
- 21 -
13.09.2022 14:38:58 13.09.2022 14:38:58