Additional Safety Warnings For Im- Pact Wrenches - VONROC IW504AC Originalbetriebsanleitung

EN
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of chil­
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak­
ing into account the working conditions and the
4
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the
power tool is maintained.
ADDITIONAL SAFETY WARNINGS FOR IM-
PACT WRENCHES
1. Hold the power tool by insulated gripping surfa­
ces, when performing an operation where the
fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed
metal parts of the power tool "live" and could
give the operator an electric shock.
2. Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
3. Check the impact socket carefully for wear,
cracks or damage before installation.
4. Hold the tool firmly.
5. Brace the tool properly before use. This tool
produces a high output torque and without
properly bracing the tool during operation, loss
of control may occur resulting in personal injury.
6. Keep hands away from rotating parts.
7. Do not touch the impact socket, bolt, nut or the
workpiece immediately after operation. They
may be extremely hot and could burn your skin.
8. Always wait until the power tool has come to
a complete stop before placing it down. The
application toolcan jam and cause you to lose
control of the power tool.
9. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high
locations.
10. The proper fastening torque may differ depen­
ding upon the kind or size of the bolt. Check the
torque with a torque wrench.
11 Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool. Use suitable de-
tectors to determine if there are hid-den supply
lines or contact the local utility companyfor
assistance.
WWW.VONROC.COM