Specifications; Specific Safety Rules - Makita GA5020C Betriebsanleitung

ENGLISH
1. Shaft lock
2. Lock button/Lock-off button
3. Switch trigger (type A)
4. Lock lever
5. Switch trigger (type B)
6. Indication lamp
7. Protrusion of loop handle
8. Matching hole in gear housing
9. Loop handle

SPECIFICATIONS

Model
Depressed center wheel diameter
Spindle thread
No load speed (n ) / Rated speed (n)
0
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to grinder
safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read all
safety warnings, instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious injury.
2. Operations such as polishing are not
recommended to be performed with this power
tool. Operations for which the power tool was not
designed may create a hazard and cause personal
injury.
3. Do not use accessories which are not specifically
designed and recommended by the tool
Explanation of general view
10. Hex wrench
11. Bolt
12. Wheel guard
13. Screw
14. Bearing box
15. Lever
16. Lock nut
17. Depressed center grinding wheel
Multi-disc
GA5020 GA5021
125 mm 125 mm
M14 M14
-1
11,000 min 11,000 min
356 mm 384 mm
2.7 kg 2.7 kg
ENE048-1
4. The rated speed of the accessory must be at least
ENF002-1
5. The outside diameter and the thickness of your
6. The arbour size of wheels, flanges, backing pads
GEB033-2
7. Do not use a damaged accessory. Before each use
8. Wear personal protective equipment. Depending
18. Inner flange
19. Lock nut wrench
20. Exhaust vent
21. Inhalation vent
22. Limit mark
23. Brush holder cap
24. Screwdriver
GA5020C/
GA6020
GA5021C
125 mm 150 mm
M14 M14
-1 -1
10,000 min 10,000 min
390 mm 356 mm
2.9 kg 3.0 kg
/II
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time.
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
GA6020C/
GA6021
GA6021C
150 mm 150 mm
M14 M14
-1 -1
10,000 min 9,000 min
384 mm 390 mm
2.8 kg 3.0 kg
-1
5