Inhaltsverzeichnis
Werbung
OBJ_BUCH-0000000167-001.book Page 24 Tuesday, January 27, 2015 9:01 AM
en
24
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
The vibrational emission values are given for dry grinding
of metal with grinding points. Other applications, such as
shaping with hard metal cutters, can lead to other vibra-
tional emission values.
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, antifouling paints for vessels, can trigger
allergic reactions to the operator or bystanders and/or
lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty the
dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Operating Instructions.
The self-start lock (for GSZ8..., GSZ11...) prevents the
straight grinder from automatically restarting again, even
after a brief interruption of the power supply during
operation, e. g., from a pulled mains plug.
The straight grinder is fitted with overload and blocking
protection (for models GSZ8..., GSZ11...). In case of
overload or blocking of the application tool, the power
supply is interrupted. In this case, switch the power tool
off, remove it from the workpiece and check the applica-
tion tool. Afterwards, switch the power tool on again.
Use a collet that fits the grinding accessory.
Insert the clamping shaft of the grinding accessory to the
stop into the collet chuck.
Observe the maximum permitted projecting shaft length
(a) of the grinding accessory according to the manufac-
turer's instructions (see page 13).
Move the power tool back and forth applying uniform
pressure, so that the workpiece surface does not become
too hot.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available through
the FEIN customer service centre.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Application tools, collet
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-DB_IA,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Selection of accessories (see page 13).
Use only original FEIN accessories. The accessories must
be intended for the power tool type.
A Collet
Werbung
Inhaltsverzeichnis
