Warranty And Liability; Declaration Of Conformity; Environmental Protection, Disposal; Connection Diagrams - Fein GRIT GIE Serie Originalbetriebsanleitung

Operating instructions.
Switching on:
Disengage and fold up the safety pushbutton (1). Press
pushbutton "I" (2).
Switching off:
Fold up safety pushbutton (1). Press pushbutton "0" (2).
After switching off, the machine runs on for
approx. 50 seconds.
Safety pushbutton:
In situations of danger, press the safety pushbutton to
switch the machine off.
Reversing the speed.
Switch position 1: Low speed
Switch position 2: High speed
The speed may only be reversed with switch (3)
when the machine is stopped.
Overload protection.
In case of continuous high load over a longer period of
time, the machine is switched off. After a cooling-down
period of approx. 15 minutes, the machine is ready for
operation again.
Working a workpiece (figures 3+4).
Make sure that the safety cover (15) is securely closed.
Check the gap clearance of the grinding rest and ensure
that both fastening screws (8) are tightened.
Check the correct adjustment and the tight seating of the
spark guard (4).
Select the speed and switch the machine on.
Place the workpiece on the grinding rest and guide it with
both hands.
Extraction device
We recommend the use of an extraction device.
The machine can be connected via sleeve (17) to an
exhauster.
Noise emission values.
A-weighted emission
pressure power level
measured at the work-
place L (re 20 μPa),
pA
in decibels
Measuring uncertainty
K , in decibels
pA
Measured A-weighted
sound power level L
wA
(re 1 pW), in decibels
Measuring uncertainty
K , in decibels
wA
Operating conditions
Speed (rpm)
Material
Dimension
Idle Sanding
78.5 91
4 4
87 98
2.5 2.5
3000 3000
– Stainless steel
Pipe, diametrer
– 42.4 mm
Wire brush
REMARK: The sum of the measured emission value and
respective measuring inaccuracy represents the upper
limit of the values that can occur during measuring.
Wear hearing protection!
Measured values determined in accordance with the cor-
responding product standard (see last page in this Instruc-
tion Manual).
Repair and customer service.
Repairs may be carried out only by qualified per-
sons in conformity with the valid regulations.
For repairs, we recommend our FEIN customer service
centre, the FEIN authorised service centres and FEIN
agencies.
When the machine's power supply cable is damaged, it
must be replaced using a specially prepared power supply
cable, available from your FEIN customer service agent.
The current spare parts list of this machine can be found
on the Internet under www.fein.com.
Carry out the following maintenance regularly:
Blow out the cooling-air openings (10) of the
motor housing with compressed air.
Remove any deposits in the housing.
If required, you can change the following parts yourself:
application tools, spark guard

Warranty and liability.

The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your machine may include only a
part of the accessories described or shown in this instruc-
tion manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
C-D1_IA, D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out machines and accessories should be
sorted for environment-friendly recycling.

Connection diagrams.

Type GIE Page 88
Type GIE2V Page 89
en
13
Idle Sanding
GRIT by Fein
– 0.35