Specifications - Makita 9563Z Betriebsanleitung

ENGLISH
1 Wheel cover
2 Bearing box
3 Screw
4 Press

SPECIFICATIONS

Depressed center wheel diameter
Spindle thread
-1
No load speed (min )
Overall length
Net weight
• Due to our continuing program of research and develop-
ment, the specifications herein are subject to change with-
out notice.
• Note: Specifications may differ from country to country.
Power supply
The machine should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. They are double-
insulated in accordance with European Standard and can,
therefore, also be used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
1. Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn when necessary. If
in doubt, wear the protective equipment.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
3. Keep guards in place.
4. Use only wheels with correct size and wheels having
a maximum operating speed at least as high as the
highest No Load Speed marked on the tool's name-
plate.When using depressed center wheels, be sure
to use only fiberglass-reinforced wheels.
5. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged wheel
immediately.
6. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
7. Do not use separate reducing bushings or adaptors
to adapt large hole abrasive wheels.
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (especially the
installing surface) or the lock nut. Damage to these
parts could result in wheel breakage.
10. For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
11. Before using the tool on an actual workpiece, test run
the tool at the highest no load speed for at least 30
seconds in a safe position. Stop immediately if there
is any vibration or wobbling that could indicate poor
installation or a poorly balanced wheel. Check the
tool to determine the cause.
12. Check that the workpiece is properly supported.
4
Explanation of general view
5 Shaft lock
6 Lock nut
7 Depressed center wheel
8 Inner flange
9560Z 9561Z
100 mm 115 mm
M10 M14
11,000 11,000
289 mm 289 mm
1.7 kg 1.7 kg
13. Hold the tool firmly.
14. Keep hands away from rotating parts.
15. Make sure the wheel is not contacting the workpiece
16. Use the specified surface of the wheel to perform the
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so that
19. Pay attention that the wheel continues to rotate after
20. Do not touch the workpiece immediately after opera-
21. Position the tool so that the power cord always stays
ENB031-4
22. If working place is extremely hot and humid, or badly
23. Do not use the tool on any materials containing
24. Do not use water or grinding lubricant.
25. Ensure that ventilation openings are kept clear when
SAVE THESE INSTRUCTIONS.
9 Lock nut wrench
10 Switch lever
11 Exhaust vent
12 Inhalation vent
9562Z 9563Z
125 mm 100 mm
M14 M10
11,000 11,000
289 mm 299 mm
1.7 kg 1.8 kg
before the switch is turned on.
grinding.
sparks fly away from you and other persons or
flammable materials.
the tool is switched off.
tion; it may be extremely hot and could burn your
skin.
behind the tool during operation.
polluted by conductive dust, use a short-circuit
breaker (30 mA) to assure operator safety.
asbestos.
working in dusty conditions. If it should become
necessary to clear dust, first disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts.
9564Z 9565Z
115 mm 125 mm
M14 M14
11,000 11,000
289 mm 299 mm
1.8 kg 1.8 kg