Specifications - Makita 9500D Betriebsanleitung

ENGLISH
1 Set plate
2 Battery cartridge
3 Screw

SPECIFICATIONS

Model
Depressed center wheel diameter ...................... 100 mm
–1
No load speed (min ) ............................................ 5,500
Overall length ..................................................... 225 mm
Net weight ...............................................................1.0 kg
Rated voltage ...................................................D.C. 7.2 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
Intended use
The tool is intended for grinding ferrous materials.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Explanation of general view
4 Outer flange
5 Depressed center wheel
6 Hex wrench
Tips for maintaining maximum battery life
1.
9500D
2.
3.
4.
ADDITIONAL SAFETY RULES FOR TOOLS
1.
2.
3.
ENC004-1
4.
5.
6.
7.
8.
9.
10. Before using the tool on an actual workpiece, let
11. Use the specified surface of the wheel to per-
12. Watch out for flying sparks. Hold the tool so that
13. Do not leave the tool running. Operate the tool
14. Do not touch the workpiece immediately after
SAVE THESE INSTRUCTIONS.
7 Shaft lock
8 Switch button
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Keep guards in place.
Use only wheels having a maximum operating
speed at least as high as "No load RPM" marked
on the tool's nameplate. When using depressed
center wheels, be sure to use only fiberglass-
reinforced wheels.
Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
Use only flanges specified for this tool.
Be careful not to damage the spindle, the flange
(especially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the wheel is not contacting the work-
piece before the switch is turned on.
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced wheel.
form the grinding.
sparks fly away from you and other persons or
flammable materials.
only when hand-held.
operation; it may be extremely hot and could
burn your skin.
3