Herunterladen Inhalt Inhalt Diese Seite drucken

Start-Up Operations; Preparation Of Start-Up Operations; Carrying Out Of Start-Up Operations; Follow-Up Of The Start-Up Operations - Aereco AWN DV Basic 101 Montage- Und Betriebsanleitung

Abluftwärmenutzungsmodul für das abluftsystem
Inhaltsverzeichnis

Werbung

EN

8. START-UP OPERATIONS

Commissioning may only be carried out in completely assembled
condition! (
)
31
8.1.

PREPARATION OF START-UP OPERATIONS

The following checks must be carried out before start-up operations:
· Check for functionality and presence of all safety-related
components.
· Remove visible defects and impurities.
· Compare the mains voltage with the specifications of the
power rating plate.
· Check the intended use.
· Check the exhaust fan with heat recovery module for safe
horizontal position.
· Check all parts, especially bolts, nuts, etc., for tightness.
· Ensure free-wheel of moving components.
· Ensure that the motor-driven ball valve is functioning correctly.
· Fill the condensate trough with water and let it drain to make
the condensate siphon work
8.2.

CARRYING OUT OF START-UP OPERATIONS

· Switch on the main switch and check smoothness
· Check the current consumption with the data on the type plate.
· After switching on, the fan automatically adjusts itself to the
factory-set pressure level of 100Pa within approx. 6 minutes.
When a stable operating point is reached, the airflows can be
controlled.
8.3.

FOLLOW-UP OF THE START-UP OPERATIONS

· Check the cooling circuit for leaks after reaching operating
temperature, if necessary tighten bolted connection
· Check the intended direction of the fluid circulation by
measuring the temperatures of the pipes.
· Complete venting of the heat exchanger.
FR

8. MISE EN SERVICE

La mise en service n'est autorisée qu'après une
installation correcte! (
8.1.
PRÉPARATION DE LA MISE EN SERVICE
Avant la première mise en service il est nécessaire de contrôler les
points suivants :
· Vérifiez la fonctionnalité et la présence de tous les composants liés à la
sécurité.
· Éliminez les débris visibles et les impuretés.
· Comparer la tension du réseau avec les données de la plaque
signalétique du ventilateur.
· Vérifiez l'utilisation prévue.
· Vérifiez que le ventilateur avec module de récupération de
chaleur est bien fixé en position horizontale et reste stable.
· Contrôler l'assemblage des pièces, notamment les vis, les
écrous, etc.
· Vérifier que le rotor tourne correctement.
· Assurez-vous que la vanne à boisseau sphérique motorisée
fonctionne correctement.
8.2.

MISE EN SERVICE ET TEST

· Allumer l'interrupteur principal et vérifier que le ventilateur est
silencieux.
· Vérifier la puissance absorbée par rapport aux données de la plaque
signalétique.
· Après la mise en marche, le ventilateur s'adapte
automatiquement au niveau de pression de 100 Pa paramétré
en usine dans un intervalle d'environ 6 minutes. Lorsqu'un
point de fonctionnement stable est atteint, les flux d'air
peuvent être contrôlés.
8.3.

SUIVI DE LA MISE EN SERVICE

· Vérifiez que le circuit de refroidissement ne présente pas de
fuites, resserrez les boulons au besoin.
· Vérifiez la direction souhaitée pour la circulation du fluide en
mesurant les températures des canalisations.
· Purge complète de l'échangeur de chaleur.
)
31
00700.95100.0004K
43 / 52

Werbung

Inhaltsverzeichnis
loading

Verwandte Produkte für Aereco AWN DV Basic 101

Inhaltsverzeichnis