Accessories - Metabo W 18 LT BL 11-125 Originalbetriebsanleitung

en ENGLISH
9. Cleaning
Remove the battery pack from the machine before
making any adjustments, changing tools,
maintaining or cleaning.
Clean the dust filter regularly: remove and clean
with a jet of compressed air.
Remove the battery pack periodically and wipe the
contact area of the battery pack and machine with a
dry cloth and remove deposits. If the battery pack
cannot be removed: see the Repairs chapter.
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and create an
electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
a suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
10. Troubleshooting
The electronic signal display (13) flashes
and the machine does not start.
The battery pack is empty; the temperature is
too high or the restart protection has triggered.
Switch the machine off and back on again.
The machine will not start if the battery pack is
inserted while the machine is on.
When using a battery pack that is not part of CAS,
the machine will not start.
The electronic signal display (13) is
permanently on.
There has been an overload while working,
therefore the performance may be reduced
temporarily. Reduce working pressure.
Electronic safety shutdown: the machine has
SHUT DOWN by itself. If the slew rate of the
current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing. See Section 4.2.

11. Accessories

Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Application:
1 = surface grinding
2 = cut-off grinding
3 = drilling of holes
4 = wire brushes
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
20
1.2 = cup wheel (ceramic)
1.3 = diamond cup wheel "masonry/concrete"
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
3.1 = diamond drill bits
4.1 = wheel brush
4.2 = cup brush
5.1 = flap disc
5.2 = backing pad for sanding sheets
prescribed guard:
Type A = cutting guard / guard incl. cutting guard
slip for cutting-off operations
Type B = guard for grinding
Type C = guard for grinding and cutting-off
operations (combination)
Type D = guard for cup wheel
Type E = extraction guard for surface grinding
Type F = extraction guard for cutting-off operations
Other accessories:
(see also www.metabo.com)
- Quick clamping nut (tool-free) (1)
- Dust filter (12)
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
- Two hole nut (21)
- Extraction guard clip
It is intended for connecting a suitable extraction
unit when cutting mineral materials, such as
reinforced concrete and masonry exclusively with
diamond cutting discs, without using water.
Order no.: 630401000; D
- Multi-position bar (24) for side handle
Permits numerous handle positions.
Order no.: 627362000
- Hand protection
Intended for work with backing pads, hook and loop
packing pads (sanding pads), wire brushes and
diamond drill bits for tiles.
Install the hand guard under the additional side-
mounted handle.
Order no.: 630327000
- Battery packs:
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah (LiHD)
Order no.: 625549000 10.0 Ah (LiHD)
etc.
- Chargers: ASC 55, ASC 145, etc.
Extraction guard for surface grinding may
only be used in conjunction with the 2-
hole nut
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
=125 mm (5'')
max