Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
11. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
See page 4.
A Roughing disc (always use with safety guard
attached)
B Louver disc (always use with safety guard
attached)
C Parting safety guard.
D Parting disc (always use with parting safety
guard attached)
E Diamond discs (always use with safety guard or
parting safety guard attached)
F Parting safety guard with guide slot (place on
machine and secure with screws.) (with adapter
for connection to a suitable dust extractor for
extraction of stone dust generated when cutting
stone slabs.)
G Hand guard (for attaching under the additional
side-mounted handle.)
H Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx. 35
mm)
I Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
J Fibre discs (always use with the hand guard
attached.)
K Steel wire brushes (always use with the hand
guard attached.)
L Bench cut-off stand
M Adjusting nut (8)
N "Quick"clamping nut
For complete range of accessories, see
www.metabo.com or refer to the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If the mains connection cable of this tool is
damaged, in order to prevent endangering
personnel and property it must be replaced by the
manufacturer, or the Customer Service of the
manufacturer, or a similarly qualified person.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
14. Technical Specifications
Explanation of details on page 3. Subject to
changes serving technical progress.
Ø
= max. diameter of accessory
t
= max. permitted thickness of clamping
max,1
shank on accessory when using clamping
nut (8)
t
= max. permitted thickness of clamping
max,2
shank on accessory when using
"Quick"clamping nut
t
= Roughing disc/Parting disc:
max,3
max. permitted thickness of accessory
M
= Spindle thread
l
= Length of the grinding spindle
n
= No-load speed (maximum speed)
P
= Nominal power input
1
P
= Power output
2
m
= Weight without mains cable
Measured values determined in conformity with
EN 60745.
Machine in protection class II
~
Alternating current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a
= Vibration emission value (sanding
h, SG
surfaces)
a
= Vibration emission value (sanding with
h, DS
sanding pad)
K
= Uncertainty (vibration)
h,SG/DS
Typical A-effective perceived sound levels:
L
= Sound pressure level
pA
L
= Acoustic power level
WA
ENGLISH en
17
Werbung
Inhaltsverzeichnis
