Makita HR3200C Betriebsanleitung Seite 9

Model HR3210FCT
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
• The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
• Wear ear protection.
• The noise emission during actual use of the power
tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Vibration
The following table shows the vibration total value (tri-
axial vector sum) determined according to applicable
standard.
Model HR3200C
Vibration
Work mode
emission
Hammer drilling
into concrete
13.7 m/s
(a )
h, HD
Chiselling
19.4 m/s
(a )
h, CHeq
Model HR3210C
Vibration
Work mode
emission
9.2 m/s
Hammer drilling
into concrete
(a ) 9.0 m/s
h, HD
7.5 m/s
Chiselling
(a )
h, CHeq
9.6 m/s
): 91 dB (A)
pA
): 102 dB (A)
WA
ENG907-1
Applicable
Uncertainty standard /
(K) Test
condition
2 2
EN62841-2-6
1.8 m/s
2 2
EN62841-2-6
1.5 m/s
Applicable
Uncertainty standard /
(K) Test
condition
2 2
EN62841-2-6
1.5 m/s
Recommended
2 2
practical
1.5 m/s
operation*
2 2
EN62841-2-6
1.5 m/s
Recommended
2 2
practical
1.5 m/s
operation*
Model HR3210FCT
Vibration
Work mode
emission
8.7 m/s
Hammer drilling
into concrete
(a ) 8.7 m/s
h, HD
6.9 m/s
Chiselling
(a )
h, CHeq
9.2 m/s
* The test condition of recommended practical operation
meets EN62841-2-6, except for the following points:
• Feed force is applied to the switch handle (main
handle) for working accuracy and efficiency.
• The side grip/handle (auxiliary handle) is held to keep
balance of the tool.
• The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared vibration total value(s) may also be used
in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared value(s)
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
Applicable
Uncertainty standard /
(K) Test
condition
2 2
EN62841-2-6
1.5 m/s
Recommended
2 2
practical
1.5 m/s
operation*
2 2
EN62841-2-6
1.5 m/s
Recommended
2 2
practical
1.5 m/s
operation*
ENG901-2
9