Maintenance And Service; Maintenance And Cleaning - Bosch PFS 3000-2 Originalbetriebsanleitung

– Set the sliding switch (25) to the appropriate application
to set the correct air flow and pressure for the spray ma-
terial used.
Off "Wood" application
Thin-viscosity spray
material
Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap (11) to do so.
Work breaks and transport (see figure K–L)
A carrying handle (23) and a carrying strap (22) are fitted to
the base unit to enable easy transport of the fine-spray sys-
tem.
You can hang the base unit (21) across your shoulder during
work using the carrying strap (22).
The spray gun (1)can be put down on a flat work surface dur-
ing breaks. No spray material can leak out.
Always put the spray gun upright on a flat surface
u
when it is filled with spray material. Spray material can
leak out from a spray gun if it is lying down.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Thoroughly clean the individual parts of the fine-spray
u
system immediately after each use, especially all
paint-carrying components. Proper cleaning is a pre-
requisite for faultless and safe operation of the spray gun.
No warranty claims will be accepted if cleaning has not
been done at all or has not been done properly.
Cleaning After Using Water-Based Paints (see figure M)
Always clean the spray gun and the spray material container
with warm water.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch off the base unit (21) and remove the air
hose (19) from the spray gun (1).
– Remove the container (7) from the spray gun (1).
Hold the container (7) underneath the suction tube (16)
Bosch Power Tools
and pull the trigger switch (5) on the spray gun so that the
spray material can flow back into the container.
– Empty the container (7).
The spray material can be stored in an airtight, sealed
"Wall" application
paint container for other applications. Use the spare
container (8) with cover or the original spray material
container, for example, for this purpose.
– Clean the container (7).
Thick-viscosity spray
– Remove the suction tube (16) with the container
material
seal (15) and rinse it thoroughly.
Reattach the suction tube (16) with the container
seal (15) to the spray gun.
– Fill the container (7) with warm water and fit it to the
spray gun (1)again.
– Connect the air hose (19) to the spray gun (1)again.
– Spray until only clear water comes out. You may have to
fill the container with warm water again.
– Remove the air hose (19) from both the base unit (21)
and the spray gun (1).
– Clean the base unit if necessary with a moistened cloth
and then remove the base unit (21) and the air hose (19)
from the immediate cleaning environment.
– Remove the cap nut (3), the air cap (2), the nozzle cap
used (10)/(11) and the suction tube (16) with the con-
tainer seal (15).
– Clean all paint-carrying parts in a bucket with warm water
using the cleaning brush (27) or with a commercially
available washing-up brush. Also clean the paint
channel (18) of the spray gun (1).
– Check that the suction tube (16) and the container
seal (15) are free of spray material and undamaged.
– Clean the ventilation hole (17) using the cleaning
brush (27).
– If required, clean the filling sieve (12) thoroughly with
warm water.
– Clean the outside of the container (7) and the spray
gun (1)with a damp cloth.
– Allow all components to dry thoroughly before assem-
bling them.
– Reassemble the fine-spray system in reverse order.
Slide the container seal (15) upwards again into the
groove of the suction tube (16).
Ensure that the container seal is positioned precisely all
around in the suction tube groove in order to seal the
spray gun correctly.
Make sure that you slide the suction tube (16) all the way
back onto the paint channel (18).
Cleaning After Using Solvent-Based Paints (see figure M)
Always clean the spray gun and the container for the spray
material with the respective diluting agent for the spray ma-
terial being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
Wear suitable gloves during cleaning work involving solvents
and solvent-based paints.
English | 25
1 609 92A 84D | (12.07.2022)