Maintenance And Service; Maintenance And Cleaning - Bosch EasySpray 18V-100 Originalbetriebsanleitung

Air cap Spray jet pattern Application
Setting the spray material quantity (see figure F)
(PAINTVolume)
– Turn the thumbwheel (5) to set the required spraying ca-
pacity:
−: Minimum quantity of spraying material,
+: Maximum quantity of spraying material.
– Start with a spray test with the minimum spray material
volume and increase the volume until the required spray
pattern is achieved. If a satisfactory spray pattern is not
achieved, dilute the spray material in 5 % increments Pre-
paring the spray material.
Please note: The intensity of the paint application is highly
dependent on the moving speed.
Spray material Setting
volume
Too much mater- The spray material volume
ial on target area must be reduced.
– Turn the thumbwheel (5)
in direction –.
Not enough ma- The spray material volume
terial on target must be increased.
area
– Turn the thumbwheel (5)
in direction +.
Dampening Wallpaper
To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap (9) to do so.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Work breaks and transport (see figure G–H)
A carrying handle (21) and a carrying strap (26) are fitted to
the base unit to enable easy transport of the fine-spray sys-
tem.
You can hang the base unit (19) across your shoulder during
work using the carrying strap (26).
Bosch Power Tools
The spray gun (1)can be put down on a flat work surface dur-
ing breaks. No spray material can leak out.
Vertical flat jet for
Always put the spray gun upright on a flat surface
u
horizontal working
when it is filled with spray material. Spray material can
direction
leak out from a spray gun if it is lying down.

Maintenance and Service

Round jet for

Maintenance and Cleaning

corners, edges and
Remove the battery from the power tool before carry-
hard to reach loca-
u
tions ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
Thoroughly clean the individual parts of the fine-spray
u
system immediately after each use, especially all
paint-carrying components. Proper cleaning is a pre-
requisite for faultless and safe operation of the spray gun.
No warranty claims will be accepted if cleaning has not
been done at all or has not been done properly.
Spare Container (Accessory) (see figure J)
You can store spray material for other applications in the air-
tight spare container (8) with cover.
Cleaning After Using Water-Based Paints (see figure K)
Always clean the spray gun and the spray material container
with warm water.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch off the base unit (19) and remove the air
hose (17) from the spray gun (1).
– Remove the container (7) from the spray gun (1).
Hold the container (7) underneath the suction tube (12)
and pull the trigger switch (6) on the spray gun so that the
spray material can flow back into the container.
– Empty the container (7).
The spray material can be stored in an airtight, sealed
paint container for other applications. Use the spare
container (8) with cover or the original spray material
container, for example, for this purpose.
– Clean the container (7).
– Remove the suction tube (12) with the container
seal (14) and rinse it thoroughly.
Reattach the suction tube (12) with the container
seal (14) to the spray gun.
– Fill the container (7) with warm water and fit it to the
spray gun (1)again.
– Connect the air hose (17) to the spray gun (1)again.
– Spray until only clear water comes out. You may have to
fill the container with warm water again.
– Remove the air hose (17) from both the base unit (19)
and the spray gun (1).
English | 23
1 609 92A 6FW | (13.12.2021)