Before First Use - HBM Machines HY4000I Bedienungsanleitung

The backlight can be switched on with the DISP button (13b). The
backlight is switched off automatically after 10 seconds.
After pressing the RESET button 5 times, the motor must
be restarted.

BEFORE FIRST USE

Use 4-stroke motor oil. SAE 10W-30 is recommended for general,
all-temperature use. Other viscosities may be used when the
average temperature is within the indicated range.
• Remove the dipstick (20) from the filling point.
• Fill the crankcase with the prescribed amount of oil.
• Replace the dipstick.
petrol, octane content at least 87.
Never add fuel when the machine is on. After use let the
machine cool down for at least 15 minutes before
refuelling.
Never smoke near the machine or the fuel. Never add fuel
• Remove the lid (21) from the filler opening.
• Pour the fuel carefully into the filler opening. Do not fill the tank
beyond the marking.
• Place the lid back on the filler opening.
On the fuel level gauge (22) on the top of the machine, you can
check the amount of fuel in the tank. F = full tank, E = tank is almost
USE
The generator must be earthed before use. This prevents
static charges that can lead to electric shock. Safety
devices from the connected electrical appliances can also
do their work (e.g. leakage current switches).
Connect a screened conductor (minimum cross-section 1.5 mm²) to
the earth connector (6) and attach the other end to a ground point
(e.g. radiator or water pipe).
Starting the motor
position for 10 to 20 seconds and then pull the starter cord
This generator can be started electrically, with remote control as well
as with starter cord.
Disconnect all connected devices before starting the
engine.
With the ignition key in RUN / REMOTE the engine is put
in standby mode. The engine must then be started within
turned to STOP before the engine can be started.
• Turn the fuel switch (16) to ON.
• Turn the ignition key to RUN/REMOTE.
Electric start
• Turn the ignition key to START until the engine starts.
• Turn the key back to RUN/REMOTE.
The ignition key must not remain on START for more than
1 second.
Start with remote control
• Press the START button on the remote control once.
The battery of the remote control has a two-year life.
Replace the battery as soon as the generator stops
responding to the remote control.
WARNING: The built-in battery is used for electrical
starting. If the battery is removed or worn, the generator
can not be started in any way.
• Turn the fuel switch (16) to ON.
• Turn the ignition key to the RUN/REMOTE position.
• Gently pull the starter cord (7) until you feel resistance.
• Give a strong pull to the starter cord. Repeat as necessary until
the engine starts.
Switch off
Disconnect all connected devices.
Turn the ignition key (17) to the STOP position or press STOP on
the remote control.
Turn the fuel switch (16) to the "OFF" position.
When used at high altitudes, the standard air-fuel mixture may
be too rich. Performance will decrease and fuel consumption will
increase.
A very rich mixture will also pollute the spark plug and cause a hard
start. If the generator is used at high altitudes, the main nozzle must
be replaced or the idle screw must be adjusted.
If the generator is always used at high altitudes, the carburetor must
be adjusted. Please contact your purchase address.
the air-fuel mixture will be too low for use at low altitudes,
causing the engine to overheat and become severely
original state.
DIRECTIONS FOR USE
Direct current and alternating current can be used simultaneously.
The DC input (12) may only be used to charge a 12V
battery.
• Set the economy switch to the "OFF" position.
• Connect the charging cable to the battery.
• Connect the positive (+) cable to the red DC input of the
generator
• Connect the negative (-) cable to the black DC input.
Risk of short circuit or sparks! Always connect the charging
the generator.
- If the cable is connected to a battery in a vehicle, the earth cable