Charging Process - DeWalt XR LI-ION DCS310 Originalanweisungen

Charging Procedure (fi g. 2)
1. Plug the charger into an appropriate outlet
before inserting battery pack.
2. Insert the battery pack (j) into the charger.
The red (charging) light will blink continuously
indicating that the charging process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, charge the battery pack fully before
first use.

Charging Process

Refer the tables below for the state of charge of the
battery pack.
State of charge–DCB100 and DCB105
charging
fully charged
hot/cold pack delay
replace battery pack
State of charge–DCB107 and DCB112
charging ––
fully charged ––––––––––––––––––––
hot/cold pack delay ––
Hot/Cold Pack Delay
DCB100 AND DCB105
When the charger detects a battery that is too hot
or too cold, it automatically starts a Hot/Cold Pack
Delay, suspending charging until the battery has
reached an appropriate temperature. The charger
then automatically switches to the pack charging
mode. This feature ensures maximum battery life.
DCB107 AND DCB112
When the charger detects a battery that is hot, it
automatically delays charging until the battery has
cooled.
When the charger detects a battery that is cold, it
automatically delays charging until the battery has
warmed.
The red light will continue to blink, but a yellow
indicator light will be illuminated during this
operation. Once the battery has cooled, the yellow
light will turn off and the charger will resume the
charging procedure.
XR Li-Ion tools are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
LI-ION BATTERY PACKS ONLY
Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
Li-Ion battery on the charger until it is fully charged.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure
to include catalog number and voltage.
The battery pack is not fully charged out of the
– – – –
carton. Before using the battery pack and charger,
–––––––––––
read the safety instructions below. Then follow
charging procedures outlined.
–– – –– –
•••••••••••
• Do not charge or use battery in explosive
–– –– –– ––
–– –– –––––––
• Never force battery pack into charger. Do
• Charge the battery packs only in D
• DO NOT splash or immerse in water or other
• Do not store or use the tool and battery
READ ALL INSTRUCTIONS
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting
or removing the battery from the charger may
ignite the dust or fumes.
not modify battery pack in any way to fit into
a non-compatible charger as battery pack
may rupture causing serious personal injury.
chargers.
liquids.
pack in locations where the temperature
may reach or exceed 40 ˚C (105 ˚F) (such as
outside sheds or metal buildings in summer).
WARNING: Never attempt to open the
battery pack for any reason. If battery
pack case is cracked or damaged,
do not insert into charger. Do not
crush, drop or damage battery pack.
Do not use a battery pack or charger
that has received a sharp blow, been
dropped, run over or damaged in any
way (i.e., pierced with a nail, hit with a
hammer, stepped on). Electric shock
or electrocution may result. Damaged
battery packs should be returned to
service centre for recycling.
EN GL IS H
WALT
E
37