Installing The Rear Wheel; Cleaning; Cleaning The Battery; Cleaning The Motor - Derby cycle Pedelec Xion 2013 Originalbetriebsanleitung

9.2

Installing the rear wheel

1. Place the torque support on the left axle side of the
motor (see point 2 in the image below).
Motormontage - Bremsseite
Motor mounting - side of the brake
6
7
2
3
4
ALBER-Komponenten
Placing the torque support
[1] Motor
[2] Drehmomentstütze in der von Ihnen bestellten Variante (Abweichung zur Grafik möglich)
Komponenten anderer Hersteller
[3] Unterlagscheibe
[4] Mutter, Anzugsmoment: 20 Nm
ACHTUNG: Zuerst die Mutter auf der gegenüberliegenden Seite anziehen, danach diese Mutter!
[5] Bremsscheibe
[6] Bremsensatz
2. Then feed the rear wheel past the rear derailleur and
[7] Rahmen des Fahrrads
Bitte beachten Sie bei Ihren Arbeiten die Vorgaben und Empfehlungen des jeweiligen Herstellers zur
Montage seiner Komponenten.
into the dropout on the frame.
ALBER Components
[1] Motor
[2] Torque receiver in the version ordered (might differ from drawing)
3. If your Pedelec has disc brakes, ensure that the brake
Components of other manufacturers
[3] Washer disc is placed exactly in the centre between the brake
[4] Nut, fastening torque: 20 Nm
ATTENTION: Tighten this nut after the one on the opposite!
blocks.
[5] Brake disc
[6] Brake set
[7] Bicycle frame
Please pay attention to the instructions of each manufacturer for the assembly of the appropriate
components.
4. Insert the rear wheel in the dropout so that the torque
support fits exactly and the ends of the axle sit entirely
within the dropout.
5. Close the quick-release device (➠ General User Manu-
al, Chapter 18.6.2 "Inserting the rear wheel ").
6. Connect the cable between the motor and the battery.
7. Attach the plug to the chain stay once more
using the rubber ring.
8. If your Pedelec has rim brakes, engage the brake cable
once more.
For precise details regarding the handling of rim or
disc brakes and quick-release devices, please refer to
the section of the User Manual concerning the tech-
nology featured in the bike.
30 VIII User Manual Pedelec Xion
1
5

10 Cleaning

› Remove the battery before you clean your
Pedelec.
› Do not use benzine, thinner, acetone or similar
agents in the cleaning procedures under any
circumstances. Likewise, the use of abrasive
cleaners and aggressive cleaning agents must
also be avoided.
› Only use commercially available, household
cleaning agents and disinfectants (isopropyl
alcohol) or water. You can obtain suitable clean-
ing agents and additional information from your
specialist cycle shop.
› We recommend you clean your Pedelec with a
damp cloth, a sponge or a brush.

10.1 Cleaning the battery

Make sure when cleaning that water does not enter the
battery. Although the electrical components are sealed,
4
it is not advisable to clean the bike by spraying it with a
hose or a high-pressure cleaner. This could damage your
bike.
When wiping down the battery, be careful not to touch and
connect the contacts on the underside. This could cause
the battery to switch off.

10.2 Cleaning the motor

Dirt should be removed from the motor of your Pedelec
regularly, ideally using a dry brush or a damp (not wet)
cloth. Running water such as that from a hose pipe or even
a high-pressure cleaner must not be used for cleaning.
The ingress of water can destroy the motor. Therefore,
ensure that neither fluids nor moisture enter the motor at
any time during cleaning.
Do not clean the motor when it is warm, e.g. immediately
after a trip. Wait until it has cooled down. Otherwise, the
motor may be damaged.