Samsung SMT-190Dx Anleitung Seite 20

USER'S MANUAL USER'S MANUAL
7. BORDER COLOR
- Split screen's border can be set in three colors.
[GRAY/WHITE/BLACK]
- Select ON/OFF or Color (GRAY, WHITE, BLACK)
using , , ,  key. Use
selection.
8. PIP POSITION
- Set Sub-screen location.
[B-RIGHT/B-LEFT/T-RIGHT/T-LEFT]
- Select PIP (B-LEFT, B-RIGHT, T-LEFT, T-RIGHT)
location using , , ,  key.
Use key to change selection.
5-2) RECORD MODE SETUP
RECORD MODE SETUP
PICTURE QUALITY
FIELD RATE
DISK END MODE
DISK END ALARM TONE
RECORD TIME MARK
RECORD TITLE MARK
1. PICTURE QUALITY
- Quality of the video to be recorded is defined in
three stages. HIGH means quality of the video to be
recorded is the highest, then NORMAL, then LOW.
[NORMAL/HIGH/LOW]
- Select video quality using , , ,  key.
Use key to change it.
2. FIELD RATE
- Set numbers of fields to be recorded.
- 8CH Mode
[NTSC][1/.5/.75/7.5 IPS]
[PAL][0.8/1.6/.1/6. IPS]
- 1CH Mode
[NTSC][1/.5/.75/7.5/15/0 IPS]
[PAL][0.8/1.6/.1/6./1.5/5 IPS]
3. DISK END MODE
- Setting to STOP will stop recording when HDD
becomes full during recording.
- Setting to CONTINUE will overwrite previously
recorded data with the one currently being recorded.
The oldest data saved in HDD will get overwritten
first. [ CONTINUE/STOP]
- Use , , ,  key to change the setup.
key to change
07/07/07 1:0:01
HIGH
7,5 IPS
STOP
ON
ON
ON
4. DISK END ALARM TONE (Notice Mode when
HDD is full)
- When DISK END MODE is set to STOP, setting
this to ON will make ALARM TONE ring when HDD
is full during recording. If it is set to OFF, ALARM
TONE will not ring. This feature won't be activated
unless DISK END MODE is set to STOP. [ON/OFF]
- Use , , , ,
5. RECORD TIME MARK
- Setting to ON will show the time when the recording
is done during playback, Setting to OFF will not
show it. [ON/OFF]
- Use , , , ,
6. RECORD TITLE MARK
- Setting to ON will show the title when the recording
is done during playback, Setting to OFF will not
show it. [ON/OFF]
- Use , , , ,
5-3) TITLE SETUP
• Function: Set the desired title of each camera.
• Setting method: Move to TITLE SETUP MENU by using
/ KEY in the SETUP MENU, and press the ENTER
key SWITCH to display the OSD as shown in the figure
below. (The figure shows the initial setting status.)
07/07/07 1:0:01
TITLE SETTING
CAMERA1
CAMERA
CAMERA
CAMERA
CAMERA5
CAMERA6
CAMERA7
CAMERA8
Move to a target camera channel by using / KEY,
then press the ENTER KEY to display a cursor
at the space of the first character in the camera title.
Move the cursor to a target character in the OSD
box lower part by using / KEY, then press the
ENTER KEY to set the character.
The cursor automatically moves to the next space after
one character is set. Set the title of camera by repeating
the same method.
(Only eight characters are available for a camera title.)
Eng-0
key to change the setup.
key to change ON or OFF.
key to make change.
07/07/07 1:0:01
TITLE SETTING
CAM1 CAMERA1
CAMERA
CAM
CAMERA
CAM
CAMERA
CAM
CAMERA5
CAM5
CAMERA6
CAM6 CAMERA7
CAMERA8
CAM7
0156789
CAM8
ABCDEFGHIJKLMNOPQ RSTUVWXYZ
:=.()[/]_+-
CAM1
CAM
CAM
CAM
CAM5
CAM6
CAM7
CAM8