SCOPREGA GE 22 RC Bedienungsanleitung Seite 6

M A N U A L O F
SAVE THIS INSTRUCTIONS MANUAL FOR REFERENCE
2. FOREWORD
Dear customer,
congratulations on choosing Scoprega.
We design and manufacture products of the highest quality to meet the needs
of our customers. Scoprega offers the highest quality in service as well. Our
specialised departments provide support and instructions when needed, as well
as comprehensive technical service.
We thank you for your trust.
WARNING
Read these instructions before using the inflator. Failure to follow all the instructions listed
below may result in damage to the product and/or cause serious injury to persons.
3. PRELIMINARY WARNINGS
1. Comply with all instructions in this document.
2. Keep these instructions.
3. Do not block air vents (SEE FIGURE 2, POINT 12 ON PAGE 3).
4. Always protect the power cable.
5. Do not open the inflator. Refer all servicing to qualified service personnel authorised by Scoprega.
Servicing is required when the device is damaged or not working in any way.
6. Do not tamper with the product. Opening the inflator will void its warranty.
7. Provide suitable ventilation.
8. Avoid placing objects near the product during operation.
9. Keep this product out of the reach of children.
10. The operating inflator produces vibrations: therefore, we recommend you to use it on the floor, so
as to avoid accidental falls.
4. INTRODUCTION
The GE 22 RC is a high-efficiency electric inflator, which stands for reliability and
functionality. The GE 22 RC is equipped with two powerful motors that allow any object to be
inflated to a pressure up to 1200 mbar. The inflator is equipped with an IP67 remote control
that allows the complete management of the pump.
5. RECOMMENDED USES
SUB/RIB/SMALL INFLATABLE ITEMS
9
I N S T R U C T I O N S
6. TECHNICAL SPECIFICATIONS
Power supply
11-14V DC
Max current
30A
Flow rate
250 l/min up to 200 mbar
120 l/min up to 1.2 bar (17 psi)
AMBIENT CONDITIONS
Max temperature
60 °C
Min temperature
-10 °C
Humidity
85% non condensing
7. GENERAL SAFETY RULES
1. ALWAYS TAKE INTO ACCOUNT THE WORKING ENVIRONMENT.
Do not expose the inflator to rain. Do not use in the presence of flammable liquids or gases.
2. AVOID UNINTENTIONAL STARTING.
Do not start the inflator with the inlet in contact with dust or water.
3. PAY ATTENTION.
Pay attention to what you are doing. Use common sense.
4. CHECK THAT THERE ARE NO DAMAGED PARTS.
Before using the inflator, carefully check its outer sides and components.
5. DO NOT OPERATE
portable inflators near flammable liquids or in gaseous or explosive
atmospheres. The inflator motors produce sparks that can release fumes.
6. DO NOT INHALE!
The compressed air coming from the inflator is not clean. Never inhale air from your inflator.
7. WARNING! RISK OF EXPLOSION.
Inflate the inflatable unit only complying with the manufacturer's recommendations. Exceeding the
pressure rating could cause the inflator to explode, resulting in personal injury.
8. NEVER LEAVE THE DEVICE UNATTENDED.
Overinflation could result in serious injury and property damage.
9. WARNING! RISK OF UNSAFE OPERATION.
Do not modify or attempt to repair the unit. Do not drill into or make any modifications to the inflator
or its accessories. Any modification to the product will void its warranty.
10. Never carry the inflator by the flexible hose or power cable.
8. USE AND OPERATION
8.1 INSTALLATION
The pumping unit must be installed in the boat compartment.
Secure the pumping unit so that boat movements do not cause any displacement and/or
movement of the boat.
Connect the supplied inflation hose, from the pumping unit to the back of the remote
control panel.
The control panel can be fixed in an area of your choice and is equipped with an IP67
cover.
The power cable of the pumping unit should be connected to a 12V battery or to the
boat's electrical system.
10