Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
al be-
complies with UNI/ECE Regulation no. 16 or
al will
other equivalent standards (Fig. 4).
• WARNING! Never fit the child car seat to a
e with
certi-
seat that is only equipped with a 2-point seat
belt (Fig. 5).
classi-
• The child car seat can be fitted on the front
t con-
passenger seat or any of the back seats. Nev-
earlier
er use this child car seat on side-facing or
rear-facing car seats (Fig. 6).
e class
• This product is expressly intended to be used
ed are:
only as a child car seat; it should not be used
indoors.
cturer
4. HOW TO FIT THE GROUP 0+ (FROM 0 UP
TO 13 kg) CHILD CAR SEAT IN THE CAR
ttach-
is not
e "Top
ailable
WARNING! When it is used for Group 0+
CAR
(from 0 up to 13 kg), always fit the child car
OINT -
seat in a rearward-facing direction. If the front
seat of the car is equipped with an airbag, de-
Teth-
activate the airbag before fitting the child car
tion is
seat. Death or serious injury hazard.
WARNING! The points through which the
patible
fic "Ap-
seat belt must pass for fitting the Group 0+
th the
seat (from 0 up to 13 kg) are highlighted in
LIGHT BLUE.
WARNING! Never use the booster cushion if
ature a
t belts
the child weighs over 9 kg.
ulation
Adjust the child car seat to position 4, the
cturer
maximum angle of inclination, using the incli-
nation adjustment lever (G), (Fig. 7).
Position the child car seat so that it faces the
ENTS
rear of the car and extract the car's 3-point
DUCT
seat belt, pulling it out as fare as possible.
Pass the abdominal and diagonal sections be-
ollow-
tween the seat and the base of the child car
e con-
seat (Fig. 8).
ty will
Fasten the buckle of the seat until you hear a
"CLICK" (Fig. 9).
or use
Begin assembly on the same side as the buck-
nd 25
le. Take the diagonal portion of the belt and
pprox-
insert completely in the red clamp (L), holding
it open (Fig. 10). Then insert the belt in the
d with
specific light blue belt guide (N) (fig. 11).
e, that
Continue to assemble on the side of the re-
All manuals and user guides at all-guides.com
tractable part of the belt. Completely insert
the belt in the red clamp (L), holding it open
(Fig. 12). Then insert the belt in the specific
light blue belt guide (N) (Fig. 13).
To make the belt as tight as possible, pull the
diagonal portion towards the retractor hold-
ing open the clamp (L) on the opposite side
(that of the buckle) so the belt can slide cor-
rectly (Fig. 14).
WARNING! Check that the child car seat is fit-
ted firmly in place and adheres correctly to the
vehicle seat; check that the seat belt is tight. If
the child car seat is not tightly and safely fitted
into the car seat, repeat the installation.
WARNING! Always check that the seat belt
is distributed evenly at all points and that it is
not twisted.
WARNING! NEVER fit the car seat belt in any
way not mentioned in these instructions.
When seating your child refer to paragraph 13.
SEATING THE CHILD IN THE CHILD CAR SEAT
5. HOW TO FIT THE GROUP 1 (9-18 kg)
WARNING! If the child weighs less than 9 kg
do not use a front-facing car seat.
To fit the car seat, remove the Isofix connec-
tors (P) by pulling belt (R) towards the exterior
(Fig. 15).
Then remove the Top Tether from the rear cov-
er (S) (Fig. 16).
Position the child car seat on the seat making
reference to the options suggested in your
car's user manual.
Fasten the two ISOFIX connectors (P) to the
corresponding ISOFIX hooks on the car seat
between the backrest and the seat (Fig. 17).
WARNING! Pull the car seat towards you and
then check that the two indicators are green
(Fig. 18) to make sure that the seat has been
installed correctly.
WARNING! Make sure there are no objects
between the child car seat and the vehicle
25
CHILD CAR SEAT TO THE CAR WITH THE
ISOFIX SYSTEM
Werbung
Inhaltsverzeichnis
