Problem Solving - Wahl 1591 Q QUICK CHARGE Betriebsanleitung

Attaching/removing the attachment comb
1. Slide the attachment comb onto the blade set (Fig. 4ⓐ) in the
direction of the arrow until it locks in place.
2. The attachment comb can be removed by pushing it in the direc-
tion of the arrow (Fig. 4ⓑ).
Maintenance
Warning! Injuries and material damage due to incorrect
handling.
f Switch off the appliance before cleaning it or performing
any maintenance and disconnect it from the mains.
Cleaning and care
Danger! Electric shock due to penetration of liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the appliance.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appliance and
accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil recom-
mended by the manufacturer.
·
Accessories are available from our dealer.
·
Spare parts are available from our service centre.
f Remove the attachment comb (Fig. 4ⓑ) and lift the blade set out
of the housing (Fig. 6ⓐ). Use the cleaning brush to remove any
cut hairs from the housing opening and from the blade set (Fig. 7).
The cleaning lever can also be pressed. This allows the cut hairs that
accumulate between the bottom blade and the top blade to be eas-
ily removed using the cleaning brush (EASY CLEANING).
f The charging contacts on the appliance and on the charging stand
should always be kept clean.
f Only wipe the appliance with a soft, slightly damp cloth.
f Oil the blade set with blade set oil (Fig. 8).
f For a good and long-lasting cutting performance, it is
important to oil the blade set frequently.
f If the cutting performance deteriorates after long use
despite regular cleaning and oiling, the blade set should
be replaced.
Changing the blade set
1. Slide the blade set off the housing in the direction of the arrow
(Fig. 6ⓐ). Remove the blade set.
2. Replace the blade set by hooking it into the housing and pressing it
down until it clicks into position (Fig. 6ⓑ).

Problem solving

Blade set is cutting badly or pulling hair out.
Cause: Blade set is dirty or worn out.
f Clean and oil the blade set. If this does not resolve the problem,
replace the blade set.
Skin injury
Cause: Too much pressure on the skin.
f Reduce pressure when cutting close to skin.
Cause: Damaged blade set.
f Check whether the blade edges were damaged during use and
replace the blade set if necessary.
Battery operating time is too short
Cause: A blade set that is very dirty and has not been oiled can reduce
the available battery operating time substantially!
f Carefully clean and oil the blade set. If the blade set is clean and
oiled and the battery operating time is still far too short, it is likely
that the batteries are nearing the end of their life.
Cause: Battery power indicator is imprecise.
f Fully discharge the appliance before fully recharging it in one unin-
terrupted charging process.
Charging indicator does not light up
Cause: The appliance must be switched off for charging.
f Check whether the appliance is switched off.
Cause: Appliance has not been correctly placed on the charging stand.
f Ensure that the appliance has been correctly placed on the charg-
ing stand.
Cause: The charging stand is not compatible with the appliance.
f Only use the charger that is included in the scope of supply. Refer
to the nameplate on the hand-held appliance and charger.
Cause: Charging contacts are dirty.
f Clean the charging contacts on the appliance and on the charging
stand.
Cause: Defective power supply.
f Make sure that there is a faultless contact between the plug-in
transformer and the socket.
f Check the mains cable for possible damage.
In the event that this information does not help you resolve your
problem, please contact our service centre. Never attempt to repair the
appliance yourself!
E N G L I S H
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
11
ar