Alert Tones; Protection Function; Program The Esc - Carson DRAGSTERBrushless-Regler Betriebsanleitung

Alert Tones

a) Input voltage abnormal alert tone:
The ESC begins to check the input voltage when power on, if it is out
of the normal range, such an alert tone will be emitted:
"beep-beep-, beep-beep-, beep-beep-" (There is 1 second time inter-
val between every "beep-beep-" tone).
GB

Protection Function

a) Low voltage cut-off protection: If the voltage of a lithium battery
pack is lower than the threshold for 2 seconds, the ESC will cut of the
output power. Please note that the ESC cannot be restarted if the
voltage of each lithium cell is lower than 3.5V.
For NiMH battery packs, if the voltage of the whole NiMH battery pack
is higher than 9.0V but lower than 12V, it will be considered as a 3 cell
lithium battery pack; If it is lower than 9.0V, it will be considered as a 2
cell lithium battery pack.
For example, if the NiMH battery pack is 8.0V, and the threshold is set
to 2.6V/Cell, so it will be considered as a 2 cell lithium battery pack,
and the low-voltage cut-off threshold for this NiMH battery pack is
2.6*2=5.2V.
c. Program the ESC
a) Program by the ESC "SET" key
12 CARSON DRAGSTER Brushless-Sport „Water resistant Version" • 50 090 6158
Turn off the ESC,
Turn on the transmitter
Hold the SET key,
Enter the corresponding
Switch on the ESC
programmable item, the RED
LED flashes for several times,
the times presents the current
value of this item.
Red LED flashes
Release
Enter the 1st item
Green LED flashes
SET key
„Running Mode"
for 1 time
Hold SET key for 3 seconds
Release
Green LED flashes
Enter the 2nd item
SET key
for 2 times
„Drag Brake Force"
Release
Green LED flashes
Enter the 3rd item
SET key
for 3 times
„Low Voltage Cut-Off"
Hold SET key for 3 seconds
......The following steps are just like the above steps......
Hold SET key for 3 seconds
Release
Green LED flashes
SET key
Enter the N
for N times
b) Throttle signal abnormal alert tone:
When the ESC can't detect the normal throttle signal, such an alert
tone will be emitted:
"beep-, beep-, beep-" (There is 2 seconds time interval between every
"beep-" tone).
b) Over-heat protection: When the temperature of the ESC is over a
factory preset threshold for 5 seconds, the ESC will cut off the output
power. You can disable the over-heat protection function for competition
race.
c) Throttle signal loss protection: The ESC will cut off the output
power if the throttle signal is lost for 0.2 second.
Press the SET key to choose the programmable
value, the RED LED flashes for several times, the
times presents the serial number of the value you
are choosing.
Red LED flashes for 1 time to choose
Press
„Forward with brake"
SET key
Red LED flashes for 2 times to choose
„Forward/Reverse with brake"
Red LED flashes 1 time, choose „0%"
Press
Red LED flashes 2 times, choose „5%"
SET key
Red LED flashes 3 times, choose „10%"
Red LED flashes 4 times, choose „20%"
Red LED flashes 5 times, choose „40%"
Red LED flashes 6 times, choose „60%"
Red LED flashes 7 times, choose „80%"
Red LED flashes 8 times, choose „100%"
Red LED flashes 1 time, choose „None"
Press
Red LED flashes 2 times, choose „2.6V"
SET key
Red LED flashes 3 times, choose „2.8V"
Red LED flashes 4 times, choose „3.0V"
Red LED flashes 5 times, choose „3.2V"
Red LED flashes 6 times, choose „3.4V"
Press SET key to choose the value, the flash
Press
times of RED LED means the serial number
SET key
th
item of the value (1 time means the 1st value, 2
times means the 2nd value...)