Herunterladen Inhalt Inhalt Diese Seite drucken

Mounting Accessories; Эксплуатация - Ferm PRM1003 Gebrauchsanweisung

Inhaltsverzeichnis

Werbung

GB
Keep your hands away from the surface to be
cut.
Electrical safety
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated;
therefore no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
. When using a cable
2
reel always unwind the reel completely.

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always
unplug the tool.
Mounting and removing cutters
Fig. B
Only use cutters with a shaft diameter which
corresponds with the size of the collet. Only use
cutters which are suited for the maximum speed
of the machine. The cutter diameter should not
exceed the maximum diameter (see 'Technical
specifications').
Press in the spindle lock (5) and turn the
spring-chuck nut (6) until it drops into the lock.
Keep the spindle lock pressed in as long as
you are following this procedure.
Use the open-end wrench to unscrew the
spring-chuck nut.
Place the cutter shaft in the collet.
Tighten the collet nut so that the cutter is
locked properly.
Open the collet nut when you want to replace
a cutter.
06
Wait until the machine has come to a
complete standstill and the cutter has
cooled down before replacing a cutter.
Mounting and adjusting the parallel guide
Fig. C
The parallel guide is a handy aid when working
on narrow workpieces.
Mount the parallel guide. Attach the guide
rods (15) on the frame (14) using the bolts
(16).
Loosen the locking bolts (9) and slide the
guide rods in the openings (8).
Adjust the parallel guide to the desired guide
distance.
Tighten the locking bolts again.
Mounting the guide bush
Fig. D
The guide bush is a handy aid for cutting a
pattern.
Mount the template guide (20) by using the
screws (17) on the cutter sole.
Mounting the adapter for dust extraction
Fig. E
Use the adapter for extracting dust.
Remove the spring-chuck nut as mentioned in
'Fitting and removing cutter bits' (Fig. B).
Loosen the clamp screw (2) for the machine
and remove the machine from the base.
Remove the clamp screws for the parallel
guide (9) on the back of the machine.
Mount the adapter for vacuum cleaning (18)
by using the screws (17) on the cutter sole
(7).
Place the clamp screws for the parallel guide
back on the cutter sole.
Place the machine back in the base and
tighten the clamp screw.
Place the spring chuck nut back on the
machine.
Place the mouthpiece of a vacuum cleaner on
the outlet of the adapter.
Keep the outlet of the machine behind
the machine for a good view on the
workpiece.
Ferm
3. УСТАНОВКА
ТЕХНОЛОГИЧЕСКОЙ
ОСНАСТКИ
Перед установкой оснастки станок
от сети.
Установка и снямие фрез
Puc. B
Используйте только те фрезы, диаметр
шпинделя которых соответствует размреу
цангового патрона. Используйте только те
фрезы, которые расчитаны на масксимаьную
скорость вращаения станка. диаметр фрезы
не должен превышать максимально
допустимояо (см. "Технические
характеристики").
Нажмите на фиксатор шпинделя (5) и
поворачивайте гайку цангового патрона (6),
пока она не дойдет до фиксатора. Во
время выполнения зтой процедуры
держите фиксатор шпинделя нажатым.
Отпустие гайку цанговояо патрона с
помощью ключа.
Установите шпиндель фрезы в цанговый
патрон.
Затяните гайку цанговояо патрона так
чтобы фреза была зажата в нужном
положении.
Когда Вам надо будет снять фрезу,
отпустите гайку цангового патрона.
Прежде чем приступать к замене
фрезы, дождитесь полной
остановки станка и дайте
возможность фрезе остыть.
Усмановка и регулировка параллельного
направляющего устройства
Puc. C
Параллельное направляющее устройство
удобно при работе с узкими заготовками.
Установите параллельное направляющее
устройство Прикрепите направляющие
стержни (16) к раме (14) с помоыо болтов
(15).
Открутите зажимные бопты (9)и вставьте
направляющие стержни в пазы (8).
Ferm
Отрегулруйте параллелное направляющее
устройство на необходимую дпину.
Снова затяните зажимные болты.
Усмановка направляющей етулки.
Puc. E
направляющея втулса является удобным
приспособлением дпя фигурного
фрезерования.
Укрепите направляющую шаблона (20)при
помощи болтов (17) на подошве фрезы.
Установка пылеулавливающей присттавки
Puc. E
Используйте приставку дпя улавливания пыли.
Удалите патрон согласно с указаниямн
вглаве «Установга и удаление фрез» (Рис.
В)
Ослабьте зажимной болт (2) машины и
извлеките её из подставки.
Удалите зажимные болты c тыльной части
машины.
Укрепите переходник для подключения
пылесоса (18) при помощи боптов (17) на
подошвеn фрезы.
Верните зажимные болты на параллельной
направляющей на их место на подошве
фрезы.
Поместите пашину обратно на подставку и
подтяните зажимный винт.
Верните патрон на его место в машине.
Подсоедините патрубок пылесоса к выходу
переходника.
Выходное отверстие должно быть
расположено за станком, чтобы не
закрывать обрабатываемую
деталь.
4. ЭКСПЛУАТАЦИЯ
Всегда соблюдайте инструкции по
безопасности, атакже нормы и
правила безопасной работы.
Станок не должен находиться в работе при
включении и выключении питания, иначе
установленная в патроне фреза может
повредить заготовку.
RUS
51

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Fbf-850e

Inhaltsverzeichnis