DeWalt DW717XPS Handbuch Seite 34

E N G L I S H
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
• Secure the workpiece.
• Although this saw will cut wood and many nonferrous materials,
these operating instructions refer to the cutting of wood only.
The same guide-lines apply to the other materials.
Do not cut ferrous (iron and steel) materials, fi bre cement or masonry
with this saw!
• Make sure to use the kerf plate. Do not operate the machine if the kerf
slot is wider than 10 mm.
Switching on and off (fi g. K)
A hole (58) is provided in the on/ off switch (1) for insertion of a padlock to
lock the tool.
• To run the tool, press the on/off switch (1).
• To stop the tool, release the switch.
Body and hand position
Proper positioning of your body and hands when operating the mitre saw
will make cutting easier, more accurate and safer.
• Never place your hands near the cutting area.
• Place your hands no closer than 150 mm from the blade.
• Hold the workpiece tightly to the table and the fence when cutting.
Keep your hands in position until the switch has been released and the
blade has completely stopped.
• Always make dry runs (without power) before fi nish cuts so that you
can check the path of the blade.
• Do not cross your hands.
• Keep both feet fi rmly on the fl oor and maintain proper balance.
• As you move the saw arm left and right, follow it and stand slightly to
the side of the saw blade.
• Sight through the guard louvres when following a pencil line.
MIter Control (fi g. E1)
The mitre lever (4) and mitre latch (5) allows the saw to mitre 60 left and
50 right.
To miter the saw:
• Release the mitre lever (4) and depress the mitre latch (5) and set the
mitre angle desired on the miter scale.
• Push down on the mitre lever (4) to lock the saw table in place.
Bevel Control (fi g. H1, H4)
The bevel latch levers (20) and bevel clamp handle (21) allows the saw
to bevel 48º left and right. Your saw has two bevel latch levers (20), one
on either side of the rear support housing. Only one needs to be used to
move the bevel to either direction. The bevel clamp handle (21) is on top of
the rear support housing.
To bevel the saw:
• Loosen the bevel clamp handle (21). Lift one of the levers to
approximately 45º and set the bevel angle desired on the bevel scale
(15). Two bevel scales are provided for convenience.
• Lock the bevel clamp handle (21) to lock the bevel in place. The bevel
latch levers (20) can be lifted vertically to override the common stop
angles.
Slide Stop (fi g. T)
The slide stop (18) control positions your saws rails so that the largest
possible verticle moldings can be cut. ALWAYS TIGHTEN THE RAIL
LOCK KNOB WHEN USING THE SLIDE STOP TO PREVENT THE SLIDE
SYSTEM FROM MOVING UNINTENTIONALLY
Rail Lock Knob (fi g. A1, T)
The rail lock knob (16) allows you to lock the saw head fi rmly to keep it
from sliding on the rails. This is necessary when making certain cuts or
when transporting the saw.
32
Grooving Stop (fi g. A1, R)
The grooving stop (17) allows for groove cutting. Flipping the lever toward
the front of the saw and adjusting the thumbscrew changes the depth of
the groove cut. Flipping the lever toward the rear of the saw bypasses the
grooving stop.
Head Lock Down Pin (fi g. A2)
To lock the saw head in the down position, push the head down, push the
pin (22) in and release the saw head. This will hold the saw head safely
down for moving the saw from place to place. To release, press the saw
head down and pull the pin out.
BASIC SAW CUTS
Vertical straight cross cut (fi g. A1, A2 & L)
• Release the mitre lever (4) and depress the mitre latch (5) to release the
mitre arm.
• Engage the mitre latch at the 0° position and tighten the mitre lever.
• Place the wood to be cut against the fence (3 & 8).
• Take hold of the operating handle (11) and depress the head lock up
release lever (12) to release the head.
• Press the trigger switch (1) to start the motor.
• Depress the head to allow the blade to cut through the timber and
enter the plastic kerf plate (9).
• After completing the cut, release the switch and wait for the saw blade
to come to a complete standstill before returning the head to its upper
rest position.
Performing a sliding cut (fi g. A1, M)
The guide rail allows cutting larger workpieces from 76.2 mm up to
111.8 mm using an out-down-back sliding motion.
• Release the rail lock knob (16).
• Pull the saw head towards you and switch the tool on.
• Lower the saw blade into the workpiece and push the head back to
complete the cut.
• Proceed as described above.
WARNING:
• Do not perform sliding cuts on workpieces smaller than
76.2 mm.
• Remember to lock the saw head in the rear position when the
sliding cuts are fi nished.
Mitre cross-cut (fi g. A1, A2 & N)
• Release the mitre lever (4) and depress the mitre latch (5).
• Move the arm left or right to the required angle. The mitre latch will
automatically locate at 10°, 15°, 22.5°, 31.62° and 45° both left and
right. If any intermediate angle is required hold the head fi rmly and lock
by tightening the mitre lever.
• Always ensure that the mitre lever is locked tightly before cutting.
• Proceed as for a vertical straight cross-cut.
WARNING: When mitring the end of a piece of wood with a
small off-cut, position the wood to ensure that the off-cut is to
the side of the blade with the greater angle to the fence; i.e. left
mitre, off-cut to the right - right mitre, off-cut to the left.
Bevel cuts (fi g. A1, A2 & O)
Bevel angles can be set from 48° left to 48° right and can be cut with the
mitre arm set between zero and a maximum of 45° mitre position right or
left.
Left bevel
• Slide the upper part of the left side fence (3) to the left as far as it will go.
• Loosen the bevel clamp handle (21), lift the bevel latch (20) and set the
bevel as desired.