Technical Data; Cordless Impact Wrench - Milwaukee M18 FID2 Originalbetriebsanleitung

TECHNICAL DATA

Production code..................................................................................
No-load speed .............................................................
Impact range ...............................................................
Max. diameter bolt / nut...............................................
No-load speed .............................................................
Impact range ...............................................................
Max. diameter bolt / nut...............................................
No-load speed .............................................................
Impact range ...............................................................
Max. diameter bolt / nut...............................................
No-load speed .............................................................
Impact range ...............................................................
Max. diameter bolt / nut...............................................
Tool reception .....................................................................................
Torque.................................................................................................
Battery voltage....................................................................................
Weight according EPTA-Procedure 01/2014 (4.0 Ah ... 6.0 Ah) ....
Weight according EPTA-Procedure 01/2014 (9.0 Ah) ........................
Recommended ambient operating temperature .................................
Recommended battery types..............................................................
Recommended charger ......................................................................
Noise information
Measured values determined according to EN 62841
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ...................................
Sound power level (Uncertainty K=3dB(A)) ........................................
Wear ear protectors!
Vibration information
Total vibration values (vector sum in the three axes) determined
according to EN 62841.
Impact tightening of fasteners of the maximum capacity of the tool
Vibration emission value a
h,ID
Uncertainty K= .................................................................................
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a „live" wire may make
exposed metal parts of the power tool „live" and could give the
operator an electric shock.
Brace the tool properly before use. This tool produces a high
output torque and without properly bracing the tool during
operation, loss of control may occur resulting in personal injury.
16 ENGLISH
470 646- M18FID2.indd 16 470 646- M18FID2.indd 16

CORDLESS IMPACT WRENCH

...........................................................
M18 FID2
.........................4812 83 01...
...000001-999999
....................... 0-1900 min
-1
....................... 0-1200 min -1
........................... M16
....................... 0-2800 min
-1
....................... 0-3400 min -1
........................... M16
....................... 0-3600 min
-1
....................... 0-4300 min -1
............................M16
....................... 0-2600 min
-1
................................ –
........................... M16
....................HEX 1/4" (6,35 mm)
............................ 226 Nm
.............................. 18 V
............................. 1,7 kg
............................. 2,1 kg
.................... -18...+50 °C
....................... M18B2, M18B4, M18B5, M18B6, M18B9
.................... M12-18C, M12-18AC, M12-18FC, M1418C6
......................... 96,75 dB (A)
....................... 107,75 dB (A)
......................... 18,63 m/s
2
............................. 1,5 m/s
2
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
28.10.2021 13:02:42 28.10.2021 13:02:42