EINHELL GE-CM 36 Li Originalbetriebsanleitung Seite 23

Charging the battery pack (Fig. 16a)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(9) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (8) into the battery
charger (9).
4. In section "Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery fails to charge, please check
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts of the charging unit
If the battery still fails to charge, send
•
the charging unit
•
and the screwdriver
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Never fully discharge the battery pack. This will
cause it to develop a defect.
Installing the battery (Fig. 16b-16d)
Open the battery cover. This is done by pulling the
snap fastener (Fig. 16b/Item A) as shown in Fig.
16b and swinging up the cover. Then insert the
two batteries in the mounts as shown in Fig. 16c.
Anl_GE_CM_36_Li_SPK13.indb 23 Anl_GE_CM_36_Li_SPK13.indb 23
GB
Notice!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 19)
Press the button for the battery capacity indicator
(Fig. 19/Item A). The battery capacity indicator
(Fig. 19/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Caution!
The lawn mover is equipped with a safety circuit
to prevent unauthorized use. Directly before st-
arting up the lawn mower insert the safety plug
(Figure 16e) and remove the safety plug again
whenever you interrupt or terminate your work.
Caution!
To prevent the equipment switching on acciden-
tally, the lawn mower is equipped with a safety
switch (Fig. 17/Item 1) which must be pressed be-
fore the switching bar (Fig. 17/Item 2) can be ac-
tivated. The lawn mower switches itself off when
the switching bar is released. Repeat this process
several times so that you are sure that the ma-
chine functions properly. Before you perform any
repair or maintenance work on the equipment,
- 23 -
14.09.2021 12:48:05 14.09.2021 12:48:05