Noise/Vibration Information - Bosch GAS 35 L AFC Professional Originalbetriebsanleitung

20 | English
Automatic start/stop
Rated voltage
230 V
Permitted connected load of the connected power tool.
These values can differ for other country-specific models. Please take note of the information on the socket of the dust extractor.

Noise/vibration information

Noise emission values determined according to EN
60335-2-69.
Typically the A-weighted sound pressure level of the dust ex-
tractor is 70 dB(A). Uncertainty K = 3 dB. The noise level
when working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a
determined according to EN 60335-2-69: a
K = 1.5 m/s
Assembly
Pull the plug out of the socket before carrying out any
u
work on the dust extractor.
Fitting the holder for the vacuum hose (see
figure A)
– Slide the holder (5) for the vacuum hose firmly into the
corresponding adapters (30) from above until they click
into place.
Fitting the vacuum hose (see figure B)
– Attach the vacuum hose (21) to the hose adapter (2) and
turn it clockwise as far as possible.
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state).
Bosch generally recommends using an anti-static vacuum
hose (accessory) to vacuum up fine dust and dry materials.
Fitting the vacuuming accessories (see figure C)
The vacuum hose (21) is equipped with a clip system which
can be used to connect vacuuming accessories (dust extrac-
tion adapter (20), curved nozzle (22)).
Fitting the nozzles and tubes
– Push the curved nozzle (22) onto the vacuum hose (21)
until you hear both snap fasteners (31) on the vacuum
hose engage.
– Then attach the required extraction accessory (floor
nozzle, crevice nozzle, suction tube, etc.) firmly to the
curved nozzle (22).
– To remove the accessory, press the snap fasteners (31)
inwards and pull apart the components.
1 609 92A 4M0 | (16.11.2018)
Downloaded from www.Manualslib.com
Maximum power
2200 W
(triax vector sum) and uncertainty K
h
<2.5 m/s
h
2
.
manuals search engine
Minimum power
100 W
Fitting the dust extraction adapter
– Push the dust extraction adapter (20) onto the vacuum
hose (21) until you hear both snap fasteners (31) on the
vacuum hose engage.
– To remove the adapter, press the snap fasteners (31) in-
wards and pull apart the components.
Inserting/removing the disposal bag or dust bag
(dry vacuuming) (see figures D1–D2)
2
,
For dry vacuuming, you can insert a disposal bag (23) or a
dust bag (accessory) into the container (1). This makes the
dust easier to dispose of.
Note: If using a paper filter bag, you must make sure that the
automatic filter cleaning is switched off; you should also do
the same if using a fleece filter bag (see "Automatic filter
cleaning (see figure H)", page 22).
Inserting the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Insert the disposal bag (23) into the container (1) with
the inlet facing forwards.
– Pull the inlet over the connection flange and all the way
into the recess of the connection flange.
– Make sure that the disposal bag (23) touches all the in-
side walls of the container (1).
– Fold the rest of the disposal bag (23) over the edge of the
container (1).
– Put the top part of the vacuum cleaner (10) on and close
the catches (11).
Removing and sealing the disposal bag
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
– Pull the full disposal bag (23) backwards out of the con-
nection flange.
– Carefully take the disposal bag (23) out of the container
(1) without damaging it.
When doing so, make sure that the disposal bag does not
scrape against the connection flange or other sharp ob-
jects.
– Remove the adhesive strip cover and tape up the disposal
bag.
Then tie up the disposal bag (23) below the inlet using
the adhesive strip cover that has been removed.
Changing/inserting the dust bag (accessory)
– Open the catches (11) and remove the top part of the va-
cuum cleaner (10).
Bosch Power Tools