Technical Data; Noise/Vibration Information - Bosch EasyVac 3 Originalbetriebsanleitung

OBJ_BUCH-2992-001.book Page 12 Thursday, December 8, 2016 10:51 AM
12 | English
Product Features
The numbering of the product features refers to the illustra-
tion of the vacuum cleaner on the graphics page.
1 Vacuum-hose holder
2 Mode selector switch
3 Cable holder
4 Socket for power tool
5 Carrying handle
6 Holder for crevice nozzle/floor nozzle
7 Hose connection piece
8 Release button for dust cup
9 Dust cup
10 Vacuum hose
11 Curved nozzle*
12 Extraction adapter
13 Crevice nozzle
14 Floor nozzle
15 Snap-fastener
16 Connection flange
17 Lid of the dust cup
18 Dust bag
19 Dust bag holder
20 Air diffuser
21 Fabric filter
22 Flat-pleated filter
23 Exhaust air cover
24 Permanent filter
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Dry vacuum cleaner
Article number
Rated voltage
Rated power input
Frequency
Container volume (gross)
Vacuum (turbine), max.
Airflow (turbine), max.
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
max. power
Rated voltage
EU/AUS 220–240 V
UK 220–240 V
* Specification of the allowable load of the connected power tool (coun-
try-specific)
1 609 92A 3FG | (8.12.16)

Noise/Vibration Information

Sound emission values determined according to
EN 60335-2-69.
Typically the A-weighted sound pressure level of the vacuum
cleaner is 73 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
determined according to EN 60335-2-69:
a < 2.5 m/s
h
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum Hose (see figure A)
– Insert the vacuum hose 10 into the hose connection piece
7 and turn it all the way in clockwise direction.
Mounting VAC Accessories
The vacuum hose 10 is equipped with a clip system, with
which the VAC accessories (extraction adapter 12, curved
nozzle 11) can be connected.
Fitting the extraction adapter or curved nozzle
(see figure B)
– Fit the extraction adapter 12 or the curved nozzle 11 to the
vacuum hose 10 until the two snap fasteners 15 of the vac-
uum hose click into place.
– To disassemble, press both snap-fasteners 15 inward and
pull the components apart.
Mounting the suction nozzles
– Then attach the required vacuuming accessory (floor noz-
zle, crevice nozzle, etc.) firmly to the curved nozzle 11 or
EasyVac 3
the extraction adapter 12.
0 603 3D1 0..
Replacing/Inserting the Dust Bag
V 220–240
(see figures C1 – C4)
W 700
For vacuuming fine dust, which is generated when working
Hz 50/60
with sanders, drills or fine saw blades, you should use a dust
l 2.1
bag (accessory). This makes the dust easier to dispose of.
mbar 240
Chips, which are generated when working with larger saws, or
l/s 35
coarser dirt can be vacuumed without using a dust bag. When
doing so, you should clean the fabric filter 21 occasionally
(see "Cleaning the Filter Assembly", page 13).
kg 4.3
/I
Replacing/Inserting the Dust Bag (Accessory)
– Press the release button 8 and pull the dust cup 9 out of
the vacuum cleaner.
– Grip the lid 17 at the connection flange 16 and remove the
lid from the dust cup.
min. power
– Turn the lid 17 over.
output output
– Put the dust bag 18 over the connection flange 16 of the
2000 W 100 W vacuum cleaner and turn the cardboard flaps under the
dust bag holder 19.
1800 W 100 W
– Press the lid 17 back onto the dust cup 9 and then slide the
dust cup back into the vacuum cleaner until it clicks into
place.
(triax vector sum) and uncertainty K
h
2 2
, K = 1.5 m/s .
Bosch Power Tools