Prior To Operation; How To Use - Hitachi DS 14DL Bedienungsanleitung

(3) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown in
Table 6.
Table 6 Charging time (At 20°C)
Charger
Battery
BCL1815, BCL1415
BCL1430, EBL1430, EBM1830
NOTE:
The charging time may vary according to temperature
and power source voltage.
4. Disconnect the charger's power cord from the
receptacle
5. Hold the charger firmly and pull out the battery
NOTE:
After charging, pull out batteries from the charger
first, and then keep the batteries properly.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries
and batteries that have not been used for an extended
period is not activated, the electric discharge might
be low when using them the first and second time.
This is a temporary phenomenon, and normal time
required for recharging will be restored by recharging
the batteries 2 – 3 times.
How to make the batteries perform longer
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery.
If you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the battery
and recharge it after it has cooled for a while.
CAUTION:
When the battery charger has been continuosly used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 15 minutes rest until the next
charging.
If the battery is recharged when it is warm due to
battery use or exposure to sunlight, the pilot lamp
lights for 1 second, does not light for 0.5 seconds (off
for 0.5 seconds).
The battery will not be recharged. In such a case, let
the battery cool before charging.

PRIOR TO OPERATION

1. Setting up and checking the work environment

HOW TO USE

UC18YGL2
1. Confirm the cap position (see Fig. 5)
Approx. 40 min.
Approx. 90 min.
(1) When using this unit as a screwdriver, line up the one
(2) When using this unit as a drill, align the cap drill mark
CAUTION:
2. Tightening torque adjustment
(1) Tightening torque
(2) Tightening torque indication
(3) Adjusting the tightening torque
CAUTION:
3. Change rotation speed
Check if the work environment is suitable by following
the precautions.
The tightening torque of this unit can be adjusted
according to the cap position, at which the cap is set.
of the numbers "1, 4, 7 ... 22" on the cap, or the black
dots, with the triangle mark on the outer body.
" " with the triangle mark on the outer body.
The cap cannot be set between the numerals "1, 4, 7
... 22" or the black dots.
Do not use with the cap numeral between "22" and
the black line at the middle of the drill mark. Doing so
may cause damage. (See Fig. 6)
Tightening torque should correspond in its intensity
to the screw diameter. When too strong torque is
used, the screw head may be broken or be injured.
Be sure to adjust the cap position according to the
screw diameter.
The tightening torque differs depending on the type
of screw and the material being tightened.
The unit indicates the tightening torque with the
numbers "1, 4, 7 ... 22" on the cap, and the black
dots. The tightening toque at position "1" is the
weakest and the torque is strongest at the highest
number. (See Fig. 5)
Rotate the cap and line up the numbers "1, 4, 7 ... 22"
on the cap, or the black dots, with the triangle mark
on the outer body. Adjust the cap in the weak or the
strong torque direction according to the torque you
need.
The motor rotation may be locked to cease while the
unit is used as drill. While operating the driver drill,
take care not to lock the motor.
Too long hammering may cause the screw broken
due to excessive tightening.
By making a combination of the switch-over of "HIGH"
or "LOW" with the shift knob and the switch-over of
Power mode (P) or Save mode (S) with the lever on
the side of the handle, the rotational speed can be set
to four (4) steps. (See "SPECIFICATIONS".)
How to switch over "HIGH" or "LOW"
Operate the shift knob to change the rotational speed.
Move the shift knob in the direction of the arrow (see
Figs. 7 and 8).
When the shift knob is set to "LOW", the drill rotates
at a low speed. When set to "HIGH", the drill rotates
at a high speed.
English
12