Electrical Connection - Galvamet GLOBE Anweisungen Zur Installation, Benutzung Und Wartung

ELECTRICAL CONNECTION

This equipment must be connected to a grounding plant.
Two types of electrical connection can be used:
1. Using a standard plug to be connected to the power cable and inserted in a mains socket which must be accessible (so that the plug can be
disconnected when servicing is carried out). Make sure that the plug is accessible also after the complete installation of the equipment.
2. By means of a fixed mains connection, fitting a bipolar switch, which ensures the disconnection, with an opening distance of the contacts
allowing a complete disconnection on the conditions of the overvoltage III category, according to installation regulations. The ground connection
(yellow-green wire) must not be interrupted.
Refer to the plate inside the hood for the mains voltage and frequency ratings.
If the power cable is damaged, it must be replaced by the manufacturer or by its service agent or a qualified person in order to avoid any risk.
OPERATION
The hood is supplied with a multispeed motor.
The hood should be run at low speed under normal conditions and at higher speeds only when there is a heavy build-up of fumes or odours.
Ideally, the hood should be switched on as soon as cooking is started and then kept on until all odours have been eliminated.
For the remote control buttons, refer to (Fig. 8) at the end of this manual.
- T1: switching on and off of the motor. The LED in the hood will flash at each pulse received from the remote control, every 10 seconds it will flash
cyclically as many times as the selected speed (1 flash = first speed, 2 flashes = second speed, 3 flashes = third speed, 4 flashes = Booster). In the
Booster speed (maximum suction), the aspirator remains in this speed for 5 minutes, after which it will automatically switch to the third speed.
- T2: switching on and off of the lighting.
- T3: increase motor speed.
- T4: decrease motor speed.
- LED S1: confirms signal transmission to the motor
- LED S2: confirms signal transmission to the lighting
- LED S3: low battery warning of the remote control.
Coding of the remote control
The supplied remote control is already coded and can be used from the beginning for total control of the hood.
In case of replacement of the remote control, or if you want to use more than one, there are 2 ways to code new remote controls.
1. Disconnect the power supply to the hood and wait 10 seconds. Re-install the hood power supply and immediately press the (T2) button on the
remote control once, wait approximately 10 seconds, after which you can use the remote control.
2. Hold down the (C1) button on the electronic board inside the hood (Fig. 10) for 4 seconds until the red programming LED (C2) lights up with a fixed
light, at this point immediately press the (T1) button on the remote control once and the LED will start to flash. When the red LED turns off, the
programming is over and the remote control can no longer be programmed.
Emergency button
In case of loss of the remote control or low power of the remote control battery, the hood can be switched on and off using the button (C1) indicated
in (Fig. 10).
Delayed self-switching off
This function allows you to programme delayed cooker hood shutdown after the end of the cooking phase which, in the shortest time possible, provides
the right level of air purity in your kitchen.
Auto power off is already preset at 15 minutes and at the first engine speed. After the 15 minutes have elapsed, the motor and the lighting switch off
automatically. To activate it, hold down the T4 key for a long time while the hood is switched on at any speed.
Light indicator for grease filter maintenance
Every 30 hours of operation of the hood, when it is switched off, the hood LED will flash for 30 seconds to warn the necessary cleaning of the metal
grease filter. To reset the timer, simply hold down the (T3) key while the LED is flashing until it is switched off. If the timer is not reset, the LED will
flash again after each time the hood is switched off again.
MAINTENANCE
Always disconnect the hood from the mains before carrying out any maintenance or cleaning operation.
Particular attention should be paid to the metallic anti-grease filters that are designed to trap particles of fat contained in the fumes. The metallic anti-
grease filters must be washed at least once a month or, if present in this model, when indicated by the electronic notice, with detergent in hot water
(or in the dish-washer). The filters may discolour after a few washes, this is normal and does not mean they have to be replaced.
To remove the grease filter, open by pulling down the lower panel of the hood and then remove the grease filter using the special handle
reinstall the anti-grease filter, reverse the operations.
It is advisable to refit the grease filters only once they are dry.
ATTENTION: the grease collected in the filters can easily catch fire and it is therefore extremely important to clean the metallic filters on a regular
basis as per instructions.
The Plasma anti-odor filter does not require any particular maintenance and its duration is about 10 years while maintaining its efficiency in eliminating
the virus odors bacteria in the air.
The hood features a LED light that, in addition to offering a good lighting and a significant energy savings, are guaranteed to last on average 10
times more than traditional lights. For replacement, contact the Assistance Service.
In order to remove the remaining glue or any impurity, the cooker hood must be cleaned immediately after installation and after having removed the
protective film.
The cooker hood must be cleaned frequently both internally and externally (at least once a month).
Do not let dirt gather on the inner and outer surfaces of the hood.
To clean the exterior of the hood do not use either acid or basic products, or abrasive sponges.
Clean the hood with a sponge dampen in warm water and a little quantity of neutral detergent (for example dishwasher detergent), in order to remove
possible particles of grease.
Rinse with a damp cloth, removing all the detergent carefully, following the satin finish direction on the steel surface.
Drying is very important, especially in areas where water is particularly hard and leaves limestone.
All the ordinary and extraordinary maintenance can be performed without having to remove the hood.
(Fig. 6). To