Important Safety Instructions; Technical Specifications; Repair Instructions - Bestway 65046 Benutzerhandbuch

OWNER'S MANUAL
WARNING

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you
don't follow these instructions, it may cause the boat to
overturn or explode and result in drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the number of
persons on board, the total weight of persons and equipment must never exceed the
maximum recommended load. Always use the seats /seating spaces provided.
2. When loading the craft, never exceed the maximum recommended load: Always load the craft
carefully and distribute loads appropriately
to maintain design trim (approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all
provisions and personal effects, any equipment not included in the light craft mass, cargo (if
any) and all consumable liquids (water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be
pre-inspected and used at all times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes,
oars, and air valves, to ensure everything is in good condition and tightly secured. If you find
any damage, please stop to repair it.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if
the boat takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to avoid going
overboard. Keep the boat balanced. Uneven distribution of persons or load in the boat may
cause the boat to overturn and result in drowning.
7. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal
waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS.
8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate
the other air chamber to prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement,
shells, glass, etc. may puncture the boat. To avoid damage, do not drag the boat on rough
surfaces.
10. When choosing an outboard motor, refer to the technical specifications section of this manual
to determine acceptable horsepower ratings.
11. For electrical motors equipped with batteries, note that battery acid can be caustic, which can
cause damage to both skin and boat materials.
12. For motors which use fuels such as gas, oil or petrol, since fuel is a flammable substance, it
should be kept away from open flames. Further, clean the boat material immediately if fuel
spatters onto the boat surface. Be aware of the potential harmful efects of liquids such as
battery acid, oil or petrol. The liquids may damage your boat.
13. Inflate according the numbered air chamber and rated pressure of the boat, or it will cause
over-inflation and potential and boat explosion. Exceeding the data given on the capacity
plate may cause the craft to be damaged, overturn and lead to drowning.
14. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
15. Know how to operate a boat. Check in your local area for information and/or training as
needed. Inform yourself about local regulations and dangers related to boating and/or other
water activities.
SAVE THESE INSTRUCTIONS
007
002
003
005
006
WARNING: To avoid damage to the boat and injury to passengers, please don't exceed
the data given on the builder's plate.

Technical Specifications

Recommended
Item Size
working pressure
7'6" x 51" x 13" 3.5 psi
65046
2.30m x 1.30m x 33cm 0.24 bar
WE SUGGEST NOT TO RETURN
THE PRODUCT TO THE STORE
QUESTIONS? PROBLEMS?
MISSING PARTS?
For FAQ, Manuals, Videos Or
Spare Parts, Please Visit
bestwaycorp.com/support
Part No. Description QTY SPARE PART NO.
001 Boat
1 P04760
001
002 Bench seat
1 F3H101ASS17
003 Floor board 1
P03777
004 Oar 1 pair
P5L334ASS19
005 Air pump 1
P05323
004
006 Drain valve
1 F3C092ASS14
007 Repair kit 1
P6J718ASS18
Floor board
Maximum load capacity
pressure
5 psi 258 kg (568.8 lbs.)
0.35 bar 2 adults
Note:
- The floorboards must be assembled before inflating the hull.
- Extended exposure to sun can shorten the lifespan of your boat. We suggest not leaving boats in
direct sunlight for more than 1 hour after use.
NOTE: Pressure gauge is for inflation purpose only, and the value of the pressure gauge is just
for reference, should not be used as a precision instrument.
- Only use Bestway approved inflation pumps.
®
- Never use motor-driven high-pressure air pumps as this may result in over-inflation.
- Under and over-inflation will result in safety hazards.
- Always check the inflation pressure before using the boat.
- Never stand on or rest objects on the boat during inflation.
- Never open the cap of air valve while the boat is in use.
- Be sure the valve is tightly closed before using the boat.
Note: When the oars are not in use, lock the oars into the Oar Clasps to avoid damage.
Outboard Motor Installation
With the boat fully inflated and in the water, attach your outboard motor onto Engine Mount at the
center of the Transom.
Note:
- Ensure the motor is always fixed on the Transom.
- Read the instruction of outboard motor for correct installation and operation.
- Overpowering a boat can result in serious injury, death or boat damage. The maximum motor
power to be used see marking on the product.
Maintenance
1. Inflate according to the PSI marked besides the valve;
2. To avoid the long-time exposure to sunshine or rain, put the outside cover on top for protection
when it not being used;
3. Clean it with mild soap water and soft cloth in case it is not going to be used for a long time.
Dry it before putting them away. Store it at a dry and shady place and keep it out of reach of
Children.
4. Use the spanner to tighten the air valve if it is leaking .
Deflation
Storage
1. Remove the Oars from the oarlocks.
Note: Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric
blowers. Doing so will cause damage and shorten the boat's life span.
4. To deflate, open the Air Valves pushing the control stem in and rotating until the valves stay
open. Deflate all the hull chambers at the same time so the air-pressure drops together. This
will prevent damage form occurring to the boat's inner structures.
5. Next deflate the Keel.
6. Disassemble the seat and floor.
7. Fold the boat from front to back to remove additional air. You can also use a pump to drain any
remaining air.

REPAIR INSTRUCTIONS:

• Fully clean the area to be repaired.
• Cut the correct size from the repair patch
material.
Apply only the amount of glue needed to cover
the repair site.
• Press the repair patch firmly to repair site for
30 seconds.
• Wait for 1 hour before inflation.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model
name ready and then visit bestwaycorp.com/support to obtain your Certificate of Origin, or you
can send e-mail to service@bestwaycorp.us for the Certificate of Origin.
Maximum motor
power
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW
2.25 kW (3 hp)
OWNER WHEN YOU SELL THE CRAFT.
3
The glue is not included in the repair kit due to
shipping constraints. You can find
silicone-based glue at most retail outlets.
Carefully read the warning labels and closely
follow instructions on the back of glue before
attempting the following repair steps.
EN