Important Safety Instructions - Bestway 65001 Bedienungsanleitung

Technical Specifications
Item 65051
2.43 m x 1.02 m (96" x 40")
Inflated Size
2.55 m x 1.17 m (100" x 46")
Deflated Size
Maximum load capacity 190 kg (418 lbs.)
Maximum number of persons 2 adults + 1 child
Maximum motor power /
Recommended working pressure 0.03 bar (0.435 psi)

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you don't follow this instructions, it may cause overturn, explode the
boat and causes to drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board, the
total weight of persons and equipment must never exceed the maximum recommended load. Always use the seats
/seating spaces provided.
2. When loading the craft, never exceed the maximum recommended load: Always load the craft carefully and distribute
loads appropriately to maintain design trim (approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and personal
effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids(water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all
times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to
ensure everything is in good condition and tightly secured. Please stop to repair if you find any damage.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to avoid going overboard. Keep the boat
balanced. Uneven distribution of persons or load in the boat may cause overturn the boat and drowning.
7. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal waves.
BE AWARE OF OFFSHORE WINDS AND CURRENTS.
8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber to
prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may
punctured the boat. To avoid damage do not drag the boat on rough surfaces.
10. When choosing an outboard motor, refer to the technical specifications section of this manual to determine
acceptable horsepower ratings.
11. For electrical motors equipped with batteries, note that battery acid can be caustic, which can cause damage to both
skin and boat materials.
12. For motors use fuel such as gas, oil, petrol, since fuel is a flammable substance and should be kept away from open
flames. Further, clean the boat material immediately if fuel spatters onto the boat surface. Be aware of the potential
harmful effects of liquids such as battery acid, oil, petrol. The liquids may damage your boat.
13. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause over inflation and boat
explosion. Exceeding the data given on the capacity plate may cause the craft to damage, overturn and lead to
drowning.
14. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
15. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself
about local regulations and dangers related to boating and/or other water activities.
SAVE THESE INSTRUCTIONS
Inflation
NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR PRODUCT AND VOID
YOUR WARRANTY
1. Screw Valve
Screw the screw valve onto the air intake valve on the boat. Open the top cover of the screw valve, insert the inflation
hose and inflate. Once inflation is finished, fasten the top cover of the screw valve.
If over inflation occurs, open the top cover of the screw valve, simply use the provided deflation pipe to deflate slightly.
Hold on the pipe until the desired pressure is reached and then fasten the top cover of the screw valve.
2. Safety Valve
Open the safety valves and inflate. Close the safety
valves after inflation and press them into the air
chambers.
When inflating your boat, never let anyone sit, step or
even lean on the boat.
Deflation
1. Screw Valve
Unscrew the screw valve from the boat.
Assembling of the boat
NEVER USE THE AIR PRESSURE MACHINE TO INFLATE
• Spread the boat on a level and even ground.
• Inflate the air chambers with a HAND air pump.
• Pay careful attention to the inflation pressure gauge during inflation. An inflation scale is provided with the product.
Inflate the product until the printed scale is charged up to the same level as that of the supplied scale. (refer the
bellowing Table and Illustration)
Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the
boat each time before using. If you use other pressure gauge, the boat pressure should not be more than the data
given on the builder's plate.
• Never stand on or rest objects on the boat during inflation.
• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.
65001 65008
3.48 m x 1.42 m (137" x 56")
3.16 m x 1.24 m (124" x 49") 2.55 m x 1.10 m (100" x 43")
3.61 m x 1.65 m (142" x 65") 3.30 m x 1.30 m (130" x 52") 2.64 m x 1.23 m (104" x 48")
252.7 kg (557.1 lbs.) 300 kg (661 lbs.)
3 adults 3 adults
1.0 kw (1.4 hp) /
0.0306 bar (0.444 psi) 0.0299 bar (0.434 psi)
Warning
2. Safety Valve
Pull out the safety valves from the air chambers. Open the safety
valves and pinch the bottom to deflate.
65060 Item Product Inflated Size
2.43 m x 1.02 m (96" x 40")
65051
3.48 m x 1.42 m (137" x 56")
65001
190 kg (418 lbs.) 65008 3.16 m x 1.24 m (124" x 49")
65060
2 adults 2.55 m x 1.10 m (100" x 43")
1.0 kw (1.4 hp)
0.03 bar (0.435 psi)
Oars Installation
1. For #65051
2. For #65001
Note: When the oars are not in use, lock the oars into the Oar Clasps to avoid damage.
Storage
1. Remove the Oars from the oarlocks.
Note: Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric blowers. Doing so will
cause damage and shorten the boat's life span.
4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together. This will
prevent damage from occurring to the boat inner structures.
5. Next deflate the floor.
6. Fold the boat from front to back to remove additional air. You can also use a pump to drain any remaining air.
Repair
1. If there is a small puncture, repair it according to the instruction on repair patch.
2. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a
speciality shop to make the repair.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit
www. bestway-service.com to obtain your Certificate of Origin, or you can send e-mail to
info@bestway-northamerica.com for the Certificate of Origin.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU SELL
THE CRAFT.
3
Deflated Size Inflated Size Chamber 2
10 cm 13.3 cm
10 cm 11.8 cm
10 cm 11 cm
10 cm 11.1 cm
NOTE: All drawings for
illustration purpose only. May
not reflect actual product.
Safety rope installation:
Put the safety rope through the rope grommets and the hole on Heavy-duty
Handle around the outside of the boat in turn, then fasten safety rope.
Note: Please carefully check whether safety rope is in perfect condition
and fastened tightly prior to each use.
Outboard Motor Installation (For #65001, #65060 only)
With the boat fully inflated and in the water, attach your outboard motor
onto Engine Mount at the center of the
Stern.
Note: Read the instruction of outboard
motor for correct installation and
operation.
Warning: Overpowering a boat can result
in serious injury, death or boat damage.
The maximum motor power to be used
see marking on the product.
Inflated Size Chamber 3
13 cm
11.8 cm
11 cm
11.1 cm
S-S-001951