Important Safety Instructions - Bestway 65096 Bedienungsanleitung

Boat
Hand Pump
Components:
• Deflation Pipe
• Heavy-duty repair patch
11
10
1 2
Heavy-duty Inflatable Inflatable
Handle Floor Cushion
7 8
Integrated
Fishing
Storage Bag Screw Valve
Rod-Holder
WARNING: To avoid damage to the boat and injury to passengers, please don't exceed the data given on the
builder's plate.
Technical Specifications
Recommended
Item Inflated Size
working pressure
2.91m x 1.27m x 46cm
0.07 bar
65096
9'6" x 50" x 18"
(1 Psi)

IMPORTANT SAFETY INSTRUCTIONS

Follow all the Safety and Operating Instructions. If you don't follow these instructions, it may cause the boat to overturn
or explode and result in drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the number of persons on board, the
total weight of persons and equipment must never exceed the maximum recommended load. Always use the seats
/seating spaces provided.
2. When loading the craft, never exceed the maximum recommended load: Always load the craft carefully and
distribute loads appropriately to maintain design trim (approximately level). Avoid placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions and personal
effects, any equipment not included in the light craft mass, cargo (if any) and all consumable liquids (water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to
ensure everything is in good condition and tightly secured. If you find any damage, please stop to repair it.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to avoid falling overboard. Keep the boat
balanced. Uneven distribution of persons or load in the boat may cause the boat to overturn and result in drowning.
7. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal waves.
BE AWARE OF OFFSHORE WINDS AND CURRENTS.
8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the other air chamber
to prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may
puncture the boat. To avoid damage, do not drag the boat on rough surfaces.
10. Inflate according to the numbered air chamber and rated pressure of the boat, or it will cause over-inflation and
potential and boat explosion. Exceeding the data given on the capacity plate may cause the craft to be damaged,
overturn and lead to drowning.
11. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
12. Know how to operate a boat. Check in your local area for information and/or training as needed. Inform yourself
about local regulations and dangers related to boating and/or other water activities.
SAVE THESE INSTRUCTIONS
Inflation
NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR PRODUCT AND VOID
YOUR WARRANTY
Note: If over inflation occurs, open the top cover of the screw valve, simply use the provided deflation pipe to deflate
slightly. Hold the pipe until the desired pressure is reached and then fasten the top cover of the screw valve.
S-S-006290/21x28.5cm(#65096)/JS-YF-2017-B-04549/英
Rope
Oar
• Inflation Scale • Screw Valve x 2
1
2
3
4
8
5
9
6
7
3 4 5
Oarlock Oar Clasp
9 10 11
Rope Safety-grab
Grommet Rope
Maximum load Maximum number
capacity of persons
270 kg (594 Ibs.) 2 adults + 1 child
Warning
Deflation
Assembling of the boat
NEVER USE THE AIR PRESSURE MACHINE TO INFLATE
• Spread the boat on a level and even ground.
• Inflate the air chambers with a HAND air pump.
• Pay careful attention to the inflation pressure gauge during inflation. An inflation scale is provided with the product.
Inflate the product until the printed scale is charged up to the same level as that of the supplied scale. (refer the
belowing Table and Illustration)
Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the pressure of the boat
each time before using. If you use other pressure gauge, the boat pressure should not be more than 0.07bar.
• Never stand on or rest objects on the boat during inflation.
• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.
Item Product Inflated Size
2.91m x 1.27m x 46cm / 9'6" x 50" x 18"
65096
6
Oar
2. Attach the oars to the oarlocks and lock them into position.
Note: When the oars are not in use, lock the oars into the Oar Clasps
to avoid damage.
Safety rope installation:
Put the safety rope through the rope grommets and the hole on
Heavy-duty Handle around the outside of the boat in turn, then fasten
safety rope. Note: Please carefully check whether safety rope is in
perfect condition and fastened tightly prior to each use.
Maintance
1. Inflate according to the PSI marked besides the valve;
2. To avoid the long-time exposure to sunshine or rain, put the outside cover on top for protection when it not being
used;
3. Clean it with mild soap water and soft cloth in case it is not going to be used for a long time. Dry it before putting them
away. Store it at a dry and shady place and keep it out of reach of Children.
Storage
1. Remove the Oars from the oarlocks.
Note: Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric blowers. Doing so will
cause damage and shorten the boat's life span.
4. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops together. This will
prevent damage from occurring to the boat inner structures.
5. Next deflate the floor.
6. Fold the boat from front to back to remove additional air. You can also use a pump to drain any remaining air.
Repair
1. If there is a small puncture, repair it according to the instruction on repair patch.
2. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the boat to a
speciality shop to make the repair.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name ready and then visit
www.bestwaycorp.com/support to obtain your Certificate of Origin, or you can send e-mail to service@bestwaycorp.us
for the Certificate of Origin.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER WHEN YOU SELL
THE CRAFT.
3
Deflated Size
10cm
NOTE: All drawings for illustration
purpose only. May not reflect actual
product.
Oars Installation
1. Connect the two shafts of the oars together; ensure the
spring-loaded pins snap into position.
Inflated Size
10.4cm