Werbung
Verfügbare Sprachen
Verfügbare Sprachen
8.
. Operati
ing instr
Risk o
of electric
Before
e measuring
verify
the connec
•
Never exc
eed the lim
specificatio
ons for eac
•
Do not tou
uch unused
•
Only use t
the meter in
that might
t exceed th
•
When a m
easuring ra
appropriat
te range.
•
Disconnec
t the test le
change fun
nctions.
•
When carr
rying out m
high ampl
itude voltag
•
Always be
careful wh
behind the
e probe bar
•
Do not me
easure curr
•
Never perf
form resist
sure all ca
pacitors in
•
"Hold" Fu
unction: Pr
operation.
8.
1 DC Volt
tage mea
Do no
ot measur
Alway
ys be carefu
behind
d the probe
when
the meter
1.
Connect th
he black tes
2.
Select the
appropriat
unknown,
always sel
3.
Connect th
he test lead
4.
The measu
ured value
8.
2 AC Volt
tage mea
Do no
ot measur
Alway
ys be carefu
behind
d the probe
when
the meter
1.
Connect t
the black te
2.
Select the
e appropria
unknown,
, always se
3.
Connect t
the test lea
4.
The meas
sured value
8.
3 DC cur
rent mea
Do not
t measure c
Curren
nt measure
jack. W
When meas
15 min
nutes break
Always
s be carefu
behind
d the probe
1.
Connect th
he black tes
measurem
ments of ma
19
.04.2010
ructions
shock dur
ring opera
g, always m
make sure t
ctions, selec
cted functio
mit value for
r protection
ch range of
measurem
terminals
when the m
n the indica
ated overvo
e indicated
d category v
ange is unk
known, alwa
eads from t
the tested
measuremen
nts on a TV
ge pulses a
at the test p
hen working
g with volta
rriers at all
times durin
ent in circu
uits with vo
ance, diode
e, transisto
the circuit
are discha
ress HOLD
to freeze t
asuremen
nts
re circuits
where vo
ul when wo
orking with
e barriers a
at all times
is linked to
o a circuit w
st lead (-) t
to the "COM
te V
rang
ge with the
ect the hig
hest possib
ds to the ci
rcuit.
and the po
olarity of th
asuremen
nts
re circuits
where vo
ul when wo
orking with
e barriers a
at all times
is linked to
o a circuit w
est lead (-)
to the "CO
ate V ∼ rang
ge with the
elect the hig
ghest possi
ds to the c
circuit.
e appears o
on the LCD
asuremen
nts
current in c
circuits with
ments: mA
A jack max.
suring curre
ents up to 1
k between 2
2 measurem
l when wor
rking with v
barriers at
t all times d
st lead (-) t
to the "COM
ax. 200mA
or to the "
DV
M92/DVM
ation. Be ve
ery careful
the meter a
and/or test
on and rang
ge.
n. This limit
t value is li
ment.
meter is lin
ked to a cir
oltage/insta
allation cate
values.
ays select t
the highest
circuit befo
ore rotating
V set or swit
tching pow
points migh
ht damage
ages above
60Vdc or 3
ng measure
ement.
ltages > 25
50V
or or contin
uity measu
rged.
he value on
nto the disp
ltages > 6
600V CAT
voltages ab
bove 60Vdc
during me
asurement
which is bei
ng tested.
M" jack and
d the red te
e FUNCTION
N switch. W
ble range a
nd lower to
e red test l
lead are dis
ltages > 6
600V CAT
voltages ab
bove 60Vdc
during me
asurement
which is bei
ng tested.
OM" jack an
nd the red t
FUNCTION
N switch. W
ble range a
and lower t
display.
h voltages
> 250V
200mA; fo
or measure
10A, max.
15s continu
ments.
voltages ab
bove 60Vdc
during mea
asurement.
M" jack and
d the red te
10A" jack f
for measure
6
M93
when mea
suring live
probes are
e not damag
sted separa
ately in the
rcuit which
is being te
egory. Nev
ver measure
t possible ra
ange and lo
g the range
selector in
er circuits,
always rem
the meter.
30Vac rms.
. Keep your
urements on
n live circui
play. Press
again to re
II may oc
cur.
c or 30Vac
rms. Keep
. Do not to
uch unused
est lead (+
) to the "V/
When the m
measuring ra
o the appro
opriate rang
splayed on
the LCD.
II may oc
cur.
c or 30Vac
rms. Keep
. Do not to
uch unused
test lead (+
+) to the "V
When the me
easuring ra
o the appro
opriate ran
ements up t
to 10A use
uous measu
urement fo
or 30Vac r
rms. Keep y
est lead (+
) to the "m
ements bet
tween 200m
Rev.
02
circuits.
ged and
e
ested.
e voltages
ower to the
e
n order to
member tha
at
r fingers
its. Make
esume norm
mal
your finge
rs
d terminals
s
/Ω" jack.
ange is
ge.
your finge
rs
d terminals
s
V/Ω" jack.
ange is
ge.
the 10A
llowed by a
a
your finger
s
mA" jack for
r
mA and 10A
A.
n nv
©Velleman
Werbung
