Safety Distances; Technical Information - Nordpeis Quadro Basic Colorado Montageanleitung

Warning! Keep the air intakes, supplying
combustion air, free from blockage.
If the requirements for ventilation are
NOT complied with, the product can overheat.
This can cause a fire.
Warrning! Extractor fans when operating
in the same room or space as the appliance
may cause problem.

3. Technical information

All products Nordpeis have secondary combustion and
are clean burning. The combustion takes place in two
phases: First the wood burns and then the gases from
the fumes are lit by the hot air. This ensures that these
new fireplaces have minimal emissions of soot particles
and un-burnt gases (such as CO) and are thus better
for the environment. Clean burning fireplaces require
a small amount of wood in order to obtain a good heat
output. Use exclusively clean and dry wood.
Weight incl.insert
Materials
Surround
Surface treatment door/
doorframe
Fuel
Operating range
Efficiency
CO % @ 13% O
2
Draught system
Combustion system
Flue outlet
Flue
Flue gas temperature
Air supply
requirements (m³/h)
Fuel charge
Refueling interval
Opening of the air vent
control
Operation
* Intermittent combustion refers to normal use of a fireplace,
i.e. new wood is inserted when the previous load has burned
down to ember
Warning: If the requirements for ventilation are
NOT complied with, the cooling airflow around the
product will be considerably reduced and
the product can overheat.
This can cause a fire.
12
160 kg
Sheet steel / Colorado concrete
Quadro Basic Colorado
Heat resistant varnish
Wood logs, 25-30 cm
6 kW nominal
80 %
0,09
Air vent control
Secondary combustion (clean
burning)
Top and rear
Outer Ø 150 mm
*Alternative versions exsists due to
National requirements
277 °C
13
1.3 kg
50 min
33%
Intermittent*

4. Safety distances

Ensure that the safety distances are complied with
(FIG 2).
When connecting a steel chimney to the top outlet
follow the assembly instructions from the producer.
Ensure to comply with the security distances required
for the steel chimney.
5. Assembly
Surround assembling instruction (FIG 5-17)
FIG 5
Prepare the place where the roomheater is going to be
installed. Makes sure the surface is free of any dust and
concrete residue. Check by the level whether the body
and the base frame of the roomheater are in correct
position. If needed corect level using base feet.
Attention! If you plan utilize rear air connection cut out
the hole in the rear wall of the base.
FIG 6
Assemble a rear wall with provided fasteners. Do not
tighten screws completly.
FIG 7
The rear wall is equiped in regulating screws.
The screws enable to correct position in realtion to
the stove body - see FIG 7B, use the level to aid setting
correct positon. In order to start and to end correction
unfasten / fasten each nut as shown on the drawing
FIG 7A,C.
FIG 8
Set the roomheater in intended place - pay attention to
safety arrangements - see in FIG 2.
Attention! If the product is placed in a corner and is
to be connected to a fresh air supply, make sure to
prepare for fresh air supply behind the product be-
fore placing the insert.
FIG 9
Prepare a front plate before assembling, set magnets in
initial position as shown on the drawing - FIG 9 A. Make
sure that regulation screw in the corner of base bottom
plate is in position as shown on FIG 9C. Prior assem-
bling check also postion of the plate - as marked by an
arrow. Assemble the plate.
FIG 10
Use the screw in the bottom, as shown in the FIG 10A,
to set final position of the front plate. If the plate is still
wobling take it out and correct position of a given
magnet or magnets. Set the gap between the plate and
lower edge of the body and its door as shown on FIG
10B.
GB