Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
(original instructions)
Rebating (fig. F)
● Fit and adjust the parallel fence.
● Proceed as for planing.
Chamfering edges
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45° angles.
● Hold the tool at an angle with the groove around the edge
of the workpiece and perform the cutting stroke.
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it.
● Unzip the bag and empty it before continuing.
Hints for optimum use
● Move the tool along the grain of the wood.
● If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only
a very thin shaving at each pass and take several passes
to achieve the desired result.
● To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
The following types of cutting blades can be obtained from
your local retailer:
- Tungsten carbide tipped reversible cutting blades
(part no. X35007, supplied per pair)
- High-speed steel reversible cutting blades
(part no. X24192-XJ11, supplied per pair)
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
@
care and regular cleaning.
Warning! Before performing any maintenance on
the tool, unplug the tool. Unplug the charger before
cleaning it.
● Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
● Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Replacing the drive belt (fig. G)
● Loosen the screws (20) and remove the cover (21).
● Remove the old drive belt.
● Place the new belt (22) over the pulleys. Place the
belt over the large pulley (23) first, then over the small
pulley (24), whilst manually rotating the belt steadily.
● Put the cover back in place and tighten the screws.
8
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
● Safely dispose of the old plug.
● Connect the brown lead to the live terminal in the
new plug.
@
● Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs. Recommended fuse: 5 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com
Technical data
Input voltage
Power input
No-load speed
Planing width
Planing depth
Rebating depth
Weight
Vibration total values (triax vector sum) according to EN 62841:
2.5 m/s
Vibration emission value (a
)
h
Level of sound pressure according to EN 62841:
Sound pressure (L
) 90 dB(A), uncertainty (K) 3 dB(A)
pA
Acoustic power (L
) 101 dB(A), uncertainty (K) 3 dB(A)
WA
EC declaration of conformity
%
MACHINERY DIRECTIVE
KW712 Planer
Black & Decker declares that these products described
KW712: type 3
V
230
AC
W
650
min
17,000
-1
mm
82
mm
2
mm
8
kg
3
, uncertainty (K) 1.5 m/s
2
2
Werbung
Inhaltsverzeichnis
