Kinderkraft SIESTA Bedienungsanleitung Seite 19

• Stop using the baby carriage if you have any doubts concerning its usage or suspect any danger.
B. ASSEMBLY
I. STROLLER PARTS
1. Frame with seat and rear
wheels
2. Front wheel x2
3. Rain cover
4. Canopy
5. Armbar
II. ASSEMBLING/DETACHING THE WHEELS
To install the front wheels (2) insert the wheels onto the tubes in the frame until a characteristic 'click' noise is heard (Fig.A).
Make sure the wheels are installed in the right place.
Front wheels can be locked so that the stroller is unable to move forward. To use this function, lift the blocking lever upwards
(Fig.B). Move the lever downwards to the initial position to unlock the front wheels (Fig.C).
In order to detach the front wheels, push and hold the button downwards and then remove the wheel (Fig.D).
NOTE! Before using the buggy make sure that all the wheels are
properly installed.
III. UNFOLDING THE FRAME
Stand the frame on a flat surface, handle up. Start unfolding the stroller by releasing the blocking element on the right side
(Fig.E). Next, pull the handle upwards (Fig.F), unfold the stroller and lock it by moving the lever downwards (see Fig.G).
IV. ASSEMBLING/DETACHING THE ARMBAR
Insert the armbar into the holes on both sides of the frame (Fig.H). If done properly, you will hear a 'click'. Belt the armbar
in the centre with the crotch protector. In order to detach the armbar, push the buttons on both sides of the armbar and
remove it (Fig.I).
V. ASSEMBLING/DETACHING AND ADJUSTING THE CANOPY
To assemble the canopy, push it onto each side of the stroller frame until you hear the 'click' noise (Fig.J), then wind the
Velcro tabs around the frame (Fig.K) and fasten the Velcro strips on the outer sides of the seat and on the backrest (Fig.L).
Make sure the canopy is properly assembled. In order to lengthen the range of the canopy, unzip the zip on the right side of
the canopy (Fig.O). You can adjust the canopy by pulling until it reaches the desired position (Fig.M). It is also possible to
lock the canopy when it is unfolded to the maximum: press the blocking mechanisms on both sides of the canopy, as shown
in Fig. N. To detach the canopy, unfasten the Velcro tabs and pull the canopy out of the frame sides.
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
VI. THE USE OF BRAKE
The baby stroller disposes of a foot parking brake on the rear axle. Step on one of the pedals to activate the brake (Fig.P).
Unlock the brake by lifting the pedal (Fig.Q).
VII. ADJUSTING THE BACKREST AND THE FOOTREST
The backrest of the stroller can be adjusted in 4 ways. In order to adjust the backrest, push the button on the back of the
seat and set the backrest in a comfortable position. Fig.R).
You can adjust the footrest in two ways (Fig.S) Press the buttons on both sides of the footrest simultaneously and set the
footrest in the chosen position.
VIII. RAIN COVER
Place the rain cover over the seat and secure it with Velcro tabs (Fig.T).
IX. SEAT BELTS
Press the buckle to unfasten the seat belts (Fig.U). To secure the child, match the shoulder belts with the hip belts, then click
them into the centre buckle until it is locked (Fig.V). Seat belts need to be adjusted each time.
X. FOLDING THE STROLLER
Fold the canopy and place the footrest in the horizontal position. Next, lift the lever on the back of the stroller to unlock it
(Fig.W). Now push the lever on the right to the inside of the stroller (Fig.X) and fold the stroller downwards by pushing the
handle forward. The blocking element preventing the unfolding of the stroller will activate automatically but make sure it is
in the right place.
XI. CARE AND MAINTENANCE The buyer is responsible for proper installation of all functional elements as well as for carrying
out all required maintenance and adjustments in order to keep the buggy in good technical condition. The buggy must be
periodically checked for potential problems. Significant measures to be applied to ensure the child's safety and prevent
shortening of the product life have been presented below:
• Check the strength and safety of all rivets and connections.
• Check all wheel locking equipment and tyres. If necessary, replace or repair.
19