Before Starting The Equipment; Fuel And Oil; Switching Off The Engine - EINHELL GC-BC 52 I AS Originalbetriebsanleitung

6. Before starting the equipment

Check the equipment for the following each time
before use:
•
That there are no leaks in the fuel system.
•
That the equipment is in perfect condition and
that the safety devices and cutting devices
are complete.
•
That all screws are securely fastened.
•
That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels
Use only a mixture of unleaded petrol and special
2-stroke engine oil. Mix the fuel mixture as indica-
ted on the fuel mixing table.
Important: Do not use a fuel mixture which has
been stored for longer than 90 days.
Important: Never use 2-stroke oil with a recom-
mended mixing ratio of 100:1. The manufacturer's
warranty will be voided in case of engine damage
due to inadequate lubrication.
Important: Only use containers designed and ap-
proved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke
oil into the mixing bottle (see scale printed on the
bottle). Then shake the bottle well.
6.2 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol
1 liter
5 liters
7. Operation
Please note that the statutory regulations gover-
ning noise abatement may diff er from town to
town.
Before starting up the equipment remove the pro-
tective caps from the cutting blade.
7.1 Starting the engine when cold
Fill the tank with the required amount of oil/petrol
mix. See "Fuel and oil".
1. Set the equipment down on a hard, level sur-
face.
2. Press the fuel pump (primer) (Fig. 1/Item 7)
10 times.
3. Move the ON/OFF switch (Fig. 1/Item 9) to "I"
4. Set the choke lever (Fig. 1/Item 5) to „ ".
5. Hold the equipment fi rmly and pull out the
Anl_GC_BC_52_I_AS_SPK9.indb 23 Anl_GC_BC_52_I_AS_SPK9.indb 23
GB
2-stroke oil
25 ml
125 ml
- 23 -
starter cable (Fig. 1/Item 4) until you feel it
start to resist. Then tug sharply on the starter
cable 2 times.
6. Set the choke lever (Fig. 1/Item 5) to „ ".
7. Hold the equipment fi rmly and pull out the
starter cable (Fig. 1/Item 4) until you feel it
start to resist. Then tug sharply on the starter
cable 4 times. The equipment should start.
Important: Never allow the starter cable to
snap back. This may damage the equipment.
Once the engine has started, allow the equip-
ment to warm up for 10 seconds.
Important: The cutting tool starts to operate
when the engine is started.
8. If the engine does not start up, repeat steps
4-8 above.
Please note: If the engine does not start up even
after several attempts, read the section "Engine
Troubleshooting". Please note: Always pull the
starter cord out in a straight line. If it is pulled out
at an angle, then friction will occur on the eyelet.
As a result of this friction, the cable will become
frayed and will wear away faster. Always hold the
starter handle when the cable retracts. Never
allow the cable to snap back when it has been
pulled out.
7.2 Starting the engine when warm
(The equipment has been idle for less than 15-20
min.)
1. Set the equipment down on a hard, level sur-
face.
2. Switch the ON/OFF switch to "I".
3. Hold the equipment fi rmly and pull out the
starter cable until you feel it start to resist.
Then tug sharply on the starter cable. The
equipment should start after 1-2 tugs. If the
equipment does not start after 6 pulls, repeat
steps 1 – 7 of the procedure for starting the
engine from cold.
7.3 Switching off the engine
Emergency Stop procedure:
If it becomes necessary to stop the equipment im-
mediately, set the ON/OFF switch to "Stop" or "0"
Normal procedure:
Let go of the throttle lever and wait until the engi-
ne has changed to idling speed. Then set the ON/
OFF switch to "Stop" or "0".
15.01.2021 08:06:25 15.01.2021 08:06:25