Seite 1
Operating instructions ⋅ Betriebsanleitung Date: 11/21 Type TW800 Connector for pressure and vacuum tests for flexible hose ® connections Adapter zur Druck- und Vakuumprüfung für flexible ® Schlauchanschlüsse - We Engineer Hightech ®...
Operating instructions Type TW800 Connector for pressure and vacuum tests for flexible hose ® connections CONTENTS INTRODUCTION For your guidance General information Warranty and liability General safety instructions Definition of qualified personnel INTENDED USE PRODUCT OVERVIEW / PRODUCT DESCRIPTION TECHNICAL DATA...
Seite 5
Safety instructions for inspection and maintenance Maintenance intervals Overview of minimum intervals for inspection and maintenance Maintenance TROUBLESHOOTING DISPOSAL ACCESSORIES The German version is the original. Manufacturer: WEH GmbH Precision Connectors - hereafter referred to as 'WEH'. Page 5 MD-10235-L51-R1.0.0-03...
1. INTRODUCTION Dear Customer, Thank you for deciding to use our products. The WEH TW800 Connector has been developed for pressure and vacuum testing on ® custom flexible hose connections. Observe and follow all instructions and warnings in these operating instructions�...
- You yourself are solely responsible for the proper performance of the replacement or repair. WEH is not responsible for the performance or any damage and/or losses aris- ing from it. WEH assumes no guarantee, warranty, product liability or other liability for any replacement or repair of the WEH Product performed by you or a third party.
Î Take appropriate safety measures if operating conditions exist that could endanger the user. Î In case of any damage that may affect the proper functioning of the WEH Product, do ® not use the WEH Product until the situation has been clarified. Disassembly of the ®...
® independently recognize and prevent potential dangers at an early stage. 2. INTENDED USE - The WEH TW800 Connector has been developed for pressure and vacuum testing ® on custom flexible hose connections. - This WEH Connector has been specially developed for your application and require- ®...
Operating instructions 4. TECHNICAL DATA Please note: Depending on the application, the technical data of your WEH Product ® may differ from these operating instructions. Please therefore observe the marking on the WEH Product itself. ® Characteristics Basic version Max. allowable operat-...
Î Store the WEH Product within a temperature range of -40 °C up to +40 °C.Storage ® temperatures outside this range may affect the service life of the WEH Product. ® Î Do not store the WEH Product in the vicinity of heat sources.
The appropriate storage period applies from the date of delivery (i.e. the date of invoicing or goods issue date as recorded by WEH or its distributor). If the Product is installed in a complete system, the storage time depends on the ®...
USIT rings should be used to seal the ports. Î Before installation, check if the counterparts are designed to withstand the assembly data (see Chapter 7.2 Installing the media line) that WEH determined for this Product. ® Note: The assembly data (torques, assembly turns etc.) are values which apply exclu- sively to the components delivered by WEH.
Operating instructions 7�2 Installing the media line Please note: Subsequent mentions of descriptions and position numbers refer to Chapter 3. Product overview / product description on page 10. Î Unscrew the protection cap from the port. A/F(1) Î When mounting media line, hold an open-ended spanner against the spanner flat A/F(1) (Figure 1).
® Î Once the connection has been made, always test the connection by tugging a little on the lower part of the WEH Connector to make sure that is fully engaged and ® that the clamping jaws are gripping correctly before introducing the pressurized test medium.
Operating instructions 8�2 Connection Î Grip the connector by its grip sleeve (Pos. 1). Î Pull the grip sleeve (Pos. 1) of the connector backwards (Figure 2). The connector is opened. Î Hold the connector by the lower part (Pos. 2) and the grip sleeve (Pos.
Operating instructions 8�3 Disconnection Î After the end of the testing procedure, fully vent the media line. Caution: First depressurize the system before releasing the connection. Î Grip the connector by its grip sleeve (Pos. 1). Î Pull the grip sleeve (Pos. 1) back (Figure 8). The connection to the hose is released and the connector can be removed by Figure 8 pulling it straight back.
Do not damage sealing surfaces or sealing components. Î Before reassembling; check the components, threads and, if present, the sealing surfaces for damage and contamination. Should you find any damage, replace the Product or send it to WEH for maintenance. Stop using the WEH Product ® ®...
– send the WEH Product immediately to WEH for maintenance. ® If the WEH Product is not regularly inspected and sent to WEH for maintenance, ® leakage may occur and under certain circumstances this may result in failures and/ or accidents.
Please note: Subsequent mentions of descriptions and position numbers refer to Chap- ter 3. Product overview / product description on page 10. Î If you detect any leaks or malfunction, replace the WEH Product or send it to WEH ®...
Operating instructions 11. DISPOSAL Î Dispose of the WEH Product appropriately when you no longer need it. Observe the ® national and local disposal regulations valid at the time of disposal. 12. ACCESSORIES Screw plug for plug version If the WEH Connector is used as a plug, the ‘B1’...
Seite 24
Betriebsanleitung Typ TW800 Adapter zur Druck- und Vakuumprüfung für flexible ® Schlauchanschlüsse INHALT EINLEITUNG Zu Ihrer Orientierung Allgemeine Angaben Gewährleistung und Haftung Allgemeine Sicherheitshinweise Definition von Fachpersonal BESTIMMUNGSGEMÄSSE VERWENDUNG PRODUKTÜBERSICHT / PRODUKTBESCHREIBUNG TECHNISCHE DATEN LAGERN Sicherheitshinweise zum sachgerechten Lagern Lagern BENÖTIGTE HILFSMITTEL...
Seite 25
Sicherheitshinweise zum Bedienen Anschließen Abschließen INSPIZIEREN | WARTEN Sicherheitshinweise zum Inspizieren und Warten Wartungsintervalle Übersicht Mindestintervalle für Inspektion und Wartung Warten FEHLERBEHEBEN ENTSORGUNG ZUBEHÖR Die deutsche Version ist das Original. Hersteller: WEH GmbH Verbindungstechnik - im Nachfolgenden „WEH“ genannt. Seite 25 MD-10235-L51-R1.0.0-03...
Sehr geehrter Kunde! Wir freuen uns, dass Sie sich für den Einsatz unseres Produktes entschieden haben. Der WEH Adapter TW800 wurde zur Druck- und Vakuumprüfung an kundenspezifischen ® flexiblen Schlauchanschlüssen entwickelt. Beachten und befolgen Sie sämtliche Hinweise und Warnungen in dieser Betriebs- anleitung�...
- ein Lieferschein - ein Original WEH Prüfprotokoll (nicht bei Ersatzteilen) - eine WEH Betriebsanleitung Î Wenden Sie sich umgehend an WEH oder den entsprechenden Vertriebspartner, falls Ihnen Unterlagen fehlen. 1�3 Gewährleistung und Haftung - Es gelten unsere allgemeinen Geschäftsbedingungen.
- der Adapter oder Teile des Adapters lösen sich unter Druck - Medien, die unter Druck stehen, heiß oder giftig sein können, treten aus - Anschlussschläuche vibrieren gefährlich Î Wenden Sie sich an WEH bevor Sie das WEH Produkt einsetzen, sollten Anweisun- ® gen in dieser Betriebsanleitung unklar sein.
Lage sind, etwaige Gefahren frühzeitig zu erkennen und zu vermeiden. 2. BESTIMMUNGSGEMÄSSE VERWENDUNG - Der WEH Adapter TW800 wurde zur Druck- und Vakuumprüfung an kundenspezi- ® fischen flexiblen Schlauchanschlüssen entwickelt. - Dieser WEH Adapter wurde speziell an Ihre Anwendung und Anforderung ange- ®...
Betriebsanleitung 4. TECHNISCHE DATEN Bitte beachten: Abhängig vom Anwendungsfall können die technischen Daten Ihres Produkts von dieser Betriebsanleitung abweichen. Beachten Sie daher stets die ® Kennzeichnung auf dem WEH Produkt selbst. ® Eigenschaften Standardausführung Max. zulässiger Vakuum bis 30 bar...
5. LAGERN 5�1 Sicherheitshinweise zum sachgerechten Lagern Î Stellen Sie sicher, dass die folgenden Sicherheitshinweise und Lagerzeiten stets ein- gehalten werden. Achtung: Eine nicht sachgerechte Lagerung des WEH Produktes kann die maximale ® Lebensdauer erheblich reduzieren. Î Schützen Sie das WEH Produkt grundsätzlich vor Beschädigungen, Verschmutz-...
Beachten Sie die Sicherheitshinweise unter Kapitel 5.1 und halten Sie die nach- folgenden Lagerzeiten ein. Die zulässige Lagerzeit gilt ab dem Auslieferungsdatum (Rechnungs-/Warenausgangsdatum seitens WEH oder dem Vertriebspartner). Sollte das WEH Produkt in einem Komplettsystem verbaut sein, so ist die Lagerzeit von ®...
Überprüfen Sie vor der Installation, ob die Gegenstücke für die Montagedaten (siehe Kapitel 7.2 Medienleitung installieren), welche WEH für das WEH Produkt vorgibt, aus- ® gelegt sind. Hinweis: Diese Montagedaten (Drehmomente, Montagedrehungen etc.) sind Werte, die ausschließlich für die Komponenten gelten, die im Lieferumfang von WEH enthalten sind. Seite 34 MD-10235-L51-R1.0.0-03...
Betriebsanleitung 7�2 Medienleitung installieren Bitte beachten: Nachfolgende Erwähnungen von Bezeichnungen und Positionsnummern beziehen sich auf das Kapitel 3. Produktübersicht / Produktbeschreibung auf Seite 30. Î Schrauben Sie die Schutzkappe von dem Anschluss ab. SW(1) Î Halten Sie beim Montieren der Medienleitung an der Schlüsselfläche SW(1) (Abbildung 1) mit einem Gabel- schlüssel gegen.
Schließen Sie den WEH Adapter nur an einwandfreie Prüflinge an. ® Î Ziehen Sie nach dem Anschließen immer am Unterteil des WEH Adapters, um ® sicherzustellen, dass er richtig angeschlossen ist und dass die Spannzangen greifen, bevor Sie das unter Druck stehende Medium zuführen.
Betriebsanleitung 8�2 Anschließen Î Greifen Sie den Adapter an der Griffhülse (Pos. 1). Î Ziehen Sie die Griffhülse (Pos. 1) des Adapters nach hinten (Abbildung 2). Der Adapter wird geöffnet. Î Halten Sie den Adapter am Unterteil (Pos. 2) und an der nach hinten gezogenen Griffhüse (Pos.
Betriebsanleitung 8�3 Abschließen Î Nach Beendigung des Prüfvorganges entlüften Sie die Medienleitung vollständig. Vorsicht: Stellen Sie zuerst den druckfreien Zustand her, bevor Sie die Verbindung lösen. Î Greifen Sie den Adapter an der Griffhülse (Pos. 1). Î Ziehen Sie die Griffhülse (Pos. 1) zurück (Abbildung 8). Dadurch wird die Verbindung zum Schlauch gelöst und der Abbildung 8 Adapter kann gerade nach hinten abgenommen werden.
Produkt nach den Wartungsarbeiten auf Leckage. Beachten ® Sie hierzu das Kapitel 7. Installieren auf Seite 34. - Zum Zweck der Inspektion ist es nicht notwendig, dass das WEH Produkt abgebaut ® wird, es muss allerdings drucklos sein und es soll kein Restmedium vorhanden sein.
Inspektion – umgehend zur Wartung an WEH. Sollten Sie das WEH Produkt nicht ® regelmäßig inspizieren und zur Wartung an WEH schicken, kann es insbesondere zu Undichtigkeiten und damit unter Umständen auch zu Ausfällen und/oder Unfällen kommen. - Bei Geräten für Kalt- und Heißwasseranwendungen ist ein Trockenlauf möglich.
Betriebsanleitung 9�3 Übersicht Mindestintervalle für Inspektion und Wartung Erstmalig Nr� Inspektion (vor Inbetrieb- Täglich Wöchentlich nahme) Dichtscheibe auf Beschädigung und Sauberkeit prüfen Äußeren Zustand auf Beschädigung und Sauberkeit prüfen Schiebehülse auf Beschädigung prüfen Spannzangen auf Funktion und Beschädigung prüfen Adapter und Medienleitung auf Leckage prüfen (siehe Kapitel 7.
Kapitel 3. Produktübersicht / Produktbeschreibung auf Seite 30. Î Tauschen Sie das WEH Produkt aus oder schicken Sie es zur Wartung an WEH ein, ® falls Sie Undichtigkeiten oder Fehlfunktionen feststellen. Das Produkt darf nicht mehr verwendet werden.
Betriebsanleitung 11. ENTSORGUNG Î Entsorgen Sie das WEH Produkt fachgerecht, wenn Sie es nicht mehr benötigen. ® Beachten Sie die zum Zeitpunkt der Entsorgung gültigen nationalen und örtlichen Bestimmungen zur Entsorgung. 12. ZUBEHÖR Verschlussschraube für Stopfenversion Sollte der WEH Adapter als Stopfen eingesetzt werden, wird der Anschluss „B1“ mit ®...