Seite 1
Operating instructions ⋅ Betriebsanleitung Type TW57 Connector for filling gas cylinders with male threads ® (with or without residual pressure valve) Adapter zum Füllen von Gasflaschen mit Außengewinde ® (mit oder ohne Restdruckventil) - We Engineer Hightech ®...
Operating instructions Type TW57 Connector for filling gas cylinders with male threads ® (with or without residual pressure valve) CONTENTS INTRODUCTION For your guidance General information Warranty and liability General safety instructions Definition of qualified personnel INTENDED USE PRODUCT OVERVIEW / PRODUCT DESCRIPTION...
Seite 5
Overview of minimum intervals for inspection and maintenance Maintenance 10. LUBRICATION 10.1 Safety instructions for lubrication 10.2 Lubrication 11. TROUBLESHOOTING 12. DISPOSAL 13. ACCESSORIES | SPARE PARTS The German version is the original. Manufacturer: WEH GmbH Precision Connectors - hereafter referred to as 'WEH'. Page 5 MD-10058-L51-R1.1.0-03...
Dear Customer, Thank you for deciding to use our products. The WEH TW57 Connector has been specially developed for filling gas cylinders ® (200 bar and 300 bar) with male threads, with or without residual pressure valve. Observe and follow all instructions and warnings in these operating instructions�...
® application and subject to strict quality controls. - You are responsible for the correct operation of the replacement or repair. WEH is not responsible for the performance or any damage and/or losses arising from it. WEH assumes no warranty, product liability or other liability for any replacement or repair performed by you or a third party.
Î Take appropriate safety measures if operating conditions exist that could endanger the user. Î In case of any damage that may affect the proper functioning of the WEH Product, do ® not use the WEH Product until the situation has been clarified. Disassembly of the ®...
2. INTENDED USE - The WEH TW57 Connector has been specially developed for filling gas cylinders ® with male threads, with or without residual pressure valve. The connector comes in many different sizes and forms.
Operating instructions 3. PRODUCT OVERVIEW / PRODUCT DESCRIPTION Product description TW57 with spring-loaded residual pressure valve pin and bail actuation Pos� Description Bail actuation RPV pin (depending on the version) Sleeve Adjustment screw Safety peg Front seal Fastening screw Definition of ports...
Seite 11
Operating instructions TW57 with spring-loaded residual pressure valve pin, bail actuation, flexible wire rope and locking device Pos� Description Flexible wire rope RPV pin (depending on the TW57 with swivel joint version) Sleeve Adjustment screw Safety peg Bail actuation Front seal...
Seite 12
Operating instructions TW57 with spring-loaded residual pressure valve pin and actuation lever Pos� Description Actuation lever Sleeve Adjustment screw Safety peg Front seal Fastening screw Definition of ports Media inlet Page 12 MD-10058-L51-R1.1.0-03...
Operating instructions 4. TECHNICAL DATA Please note: Depending on the application, the technical data of your WEH Product ® may differ from these operating instructions. Please therefore observe the marking on the WEH Product itself. ® Characteristics Basic version PN = 200 bar | PS = 250 bar *...
5�1 Safety instructions for proper storage Î Make sure that you always comply with these following safety instructions and storage time. Attention: Improper storage of the WEH Product can significantly reduce the ® maximum service life. Î Protect the WEH Product against damage, contamination, inappropriate storage ®...
The appropriate storage period applies from the date of delivery (i.e. the date of invoicing or goods issue date as recorded by WEH or its distributor). If the Product is installed in a complete system, the storage time depends on the ®...
Î Check the WEH Product for transport damages, contamination and other damage. ® If you should detect anything wrong with the WEH Product, it may no longer be used. ® Replace the WEH Product or send it to WEH for maintenance.
Operating instructions 7�2 Installing the media hose line Please note: Subsequent mentions of descriptions and position numbers refer to chapter 3. Product overview / product description on page 10. Î Unscrew the protection cap from the port. Î When mounting the filling hose, hold an open-ended A/F(1) spanner against the spanner flat A/F(1) (Figure 2).
® jaws are gripping correctly before introducing the pressurized test medium. Î The clamping jaws of the WEH Connector are designed to grip the cylinder valve ® firmly. Keep fingers and other objects away from the clamping jaws when actuating the connector.
In particular, the connector must be fully depressurized during the connection process. 8�2 Connection Connecting a TW57 with bail actuation and actuation lever Î Fold the actuation unit (Pos. 1) upwards (Figure 3). Î...
Seite 20
Operating instructions Connecting a TW57 with bail actuation, flexible wire rope and locking device Î Fold the actuation bail (Pos. 6) downwards and pull at the locking device (Pos. 8) at the same time (Figure 7). The flexible wire rope will fold upwards and the clamping jaws will open.
(Pos. 5) on the connector can retract and the actuation is no longer blocked (Figure 11). Figure 11 Disconnecting a TW57 with bail actuation and actuation lever Î Fold the actuation unit (Pos. 1) upwards as far as it will go (Figure 12).
Seite 22
Operating instructions Disconnecting a TW57 with bail actuation, flexible wire rope and locking device Î Fold the actuation bail (Pos. 6) downwards and pull at the locking device (Pos. 8) at the same time (Figure 14). The flexible wire rope will fold upwards and the clamping jaws will open.
Do not damage sealing surfaces or sealing components. Î Before reassembling; check the components, threads and, if present, the sealing surfaces for damage and contamination. Should you find any damage, replace the Product or send it to WEH for maintenance. Stop using the WEH Product ® ®...
– send the WEH Product immediately to WEH for maintenance. ® If the WEH Product is not regularly inspected and sent to WEH for maintenance, ® leakage may occur and under certain circumstances this may result in failures and/or accidents.
WEH for maintenance. Î Check the residual pressure valve pin (Pos. 2), if provided, for tightness and any damage. If the RPV pin is loose, damaged or bent, send the product back to WEH for maintenance. Î...
Seite 27
Operating instructions 9�4�1 Replacement of front seal (Pos� 7) Î Position the WEH Connector ® vertically and flip the actuation over so that the adapter is ready for connection. Î Insert a suitable repair tool behind the front seal (Pos. 7)
Lubricant part No. E99-44923 for lubrication. ® 10�2 Lubrication Î Apply with a small screwdriver a thin film of WEH Lubricant ® between the cams (red arrow, Figure 16 and Figure 17). Attention: The lubricant must not be allowed to enter the gas channel.
Product appropriately when you no longer need it. Observe the ® national and local disposal regulations valid at the time of disposal. 13. ACCESSORIES | SPARE PARTS Adaptors Various adaptors are available to connect the ‘B1’ media inlet of the WEH Product to the ® filling hose. Actuation Various actuation units such as bails, wire ropes etc.
Seite 32
Betriebsanleitung Typ TW57 Adapter zum Füllen von Gasflaschen mit Außengewinde ® (mit oder ohne Restdruckventil) INHALT EINLEITUNG Zu Ihrer Orientierung Allgemeine Angaben Gewährleistung und Haftung Allgemeine Sicherheitshinweise Definition von Fachpersonal BESTIMMUNGSGEMÄSSE VERWENDUNG PRODUKTÜBERSICHT / PRODUKTBESCHREIBUNG TECHNISCHE DATEN LAGERN Sicherheitshinweise zum sachgerechten Lagern Lagern BENÖTIGTE HILFSMITTEL...
Seite 33
Übersicht Mindestintervalle für Inspektion und Wartung Warten 10. SCHMIEREN 10.1 Sicherheitshinweise zum Schmieren 10.2 Schmieren 11. FEHLERBEHEBEN 12. ENTSORGEN 13. ZUBEHÖR | ERSATZTEILE Die deutsche Version ist das Original. Hersteller: WEH GmbH Verbindungstechnik - im Nachfolgenden „WEH“ genannt. Seite 33 MD-10058-L51-R1.1.0-03...
Sehr geehrter Kunde, Wir freuen uns, dass Sie sich für den Einsatz unseres Produktes entschieden haben. Der WEH Adapter TW57 wurde zum Füllen von Gasflaschen (200 bar und 300 bar) mit ® Außengewinde, mit oder ohne Restdruckventil entwickelt. Beachten und befolgen Sie sämtliche Hinweise und Warnungen in dieser Betriebs- anleitung�...
- ein Lieferschein - ein Original WEH Prüfprotokoll (nicht bei Ersatzteilen) - eine WEH Betriebsanleitung Î Wenden Sie sich umgehend an WEH oder den entsprechenden Vertriebspartner, falls Ihnen Unterlagen fehlen. 1�3 Gewährleistung und Haftung - Es gelten unsere allgemeinen Geschäftsbedingungen.
Stellen Sie diese Betriebsanleitung insbesondere jedem zur Verfügung, der für die Installation, Bedienung und Wartung dieses WEH Produktes zuständig ist. ® Î Wenden Sie sich an WEH bevor Sie das WEH Produkt einsetzen, sollten Anweisun- ® gen in dieser Betriebsanleitung unklar sein. Î...
Lage sind, etwaige Gefahren frühzeitig zu erkennen und zu vermeiden. 2. BESTIMMUNGSGEMÄSSE VERWENDUNG - Der WEH Adapter TW57 wurde zum Füllen von Gasflaschen mit Außengewinde, ® mit oder ohne Restdruckventil entwickelt. Es gibt den Adapter in vielen verschieden Größen und Formen.
Betriebsanleitung 3. PRODUKTÜBERSICHT / PRODUKTBESCHREIBUNG Produktbeschreibung TW57 mit gefedertem RPV-Pin und Betätigungsbügel Pos� Bezeichnung Betätigungsbügel RPV-Pin (je nach Ausführung) Hülse Stellschraube Sicherheitsstift Frontdichtung Befestigungsschraube Begriffserklärung Anschlüsse Betriebsmedienzuleitung Seite 38 MD-10058-L51-R1.1.0-03...
Seite 39
Betriebsanleitung TW57 mit gefedertem RPV-Pin, Betätigungsbügel, flexiblem Drahtseil und Arretierung Pos� Bezeichnung Flexibles Drahtseil TW57 mit Drehdurchführung RPV-Pin (je nach Ausführung) Hülse Stellschraube Sicherheitsstift Betätigungsbügel Frontdichtung Arretierung Befestigungsschraube Drehduchfühung Begriffserklärung Anschlüsse Betriebsmedienzuleitung Seite 39 MD-10058-L51-R1.1.0-03...
Seite 40
Betriebsanleitung TW57 mit gefedertem RPV-Pin und Betätigungshebel Pos� Bezeichnung Betätigungshebel Hülse Stellschraube Sicherheitsstift Frontdichtung Befestigungsschraube Begriffserklärung Anschlüsse Betriebsmedienzuleitung Seite 40 MD-10058-L51-R1.1.0-03...
Prüfungen / Sauerstoffausbrandprüfung vorhanden Zulassungen * Beachten Sie die maximalen Druckvorgaben der entsprechenden Flaschenventilnorm. Diese können niedriger sein als der maximal zulässige Betriebsdruck für den das WEH Produkt ausgelegt ist. ® ** anderer Gase, je nach Auftragsbestätigung möglich ***abhängig vom Anwendungsfall Seite 41 MD-10058-L51-R1.1.0-03...
5. LAGERN 5�1 Sicherheitshinweise zum sachgerechten Lagern Î Stellen Sie sicher, dass die folgenden Sicherheitshinweise und Lagerzeiten stets eingehalten werden. Achtung: Eine nicht sachgerechte Lagerung des WEH Produktes kann die maximale ® Lebensdauer erheblich reduzieren. Î Schützen Sie das WEH Produkt grundsätzlich vor Beschädigungen, Verschmutz-...
Beachten Sie die Sicherheitshinweise unter Kapitel 5.1 und halten Sie die nach- folgenden Lagerzeiten ein. Die zulässige Lagerzeit gilt ab dem Auslieferungsdatum (Rechnungs-/Warenausgangsdatum seitens WEH oder dem Vertriebspartner). Sollte das WEH Produkt in einem Komplettsystem verbaut sein, so ist die Lagerzeit von ®...
Kapitel 7.2 Medienleitung installieren), welche WEH für das WEH Produkt vorgibt, aus- ® gelegt sind. Hinweis: Diese Montagedaten (Drehmomente, Montagedrehungen etc.) sind Werte, die ausschließlich für die Komponenten gelten, die im Lieferumfang von WEH enthalten sind. Î Verwenden Sie USIT-Ringe zum Abdichten der zylindrischen Anschlüsse. Î...
Betriebsanleitung 7�2 Medienleitung installieren Bitte beachten: Nachfolgende Erwähnungen von Bezeichnungen und Positionsnummern beziehen sich auf das Kapitel 3. Produktübersicht / Produktbeschreibung auf Seite 38. Î Schrauben Sie die Schutzkappe von dem Anschluss ab. Î Halten Sie beim Montieren des Füllschlauches an der SW(1) Schlüsselfläche SW(1) (Abbildung 2) mit einem Gabel- schlüssel gegen.
Adapter gerade an, dadurch wird einer Beschädigung der ® Frontdichtung durch eventuell scharfe Kanten am Prüfling vorgebeugt. Î Ziehen Sie nach dem Anschließen immer am WEH Adapter, um sicherzustellen, ® dass er richtig angeschlossen ist und dass die Spannzangen greifen, bevor Sie das unter Druck stehende Medium zuführen.
Schließen Sie den Adapter nur bei absolut sicheren Verhältnissen ab. Insbesondere muss der Adapter beim Abschlussvorgang vollständig drucklos sein. 8�2 Anschließen Anschließen eines TW57 mit Bügelbetätigung und Betätigungshebel Î Klappen Sie die Betätigung (Pos. 1) nach oben (Abbildung 3). Î...
Seite 48
Betriebsanleitung Anschließen eines TW57 mit Betätigungsbügel, flexiblem Drahtseil und Arretierung Î Klappen Sie die Betätigungsbügel (Pos. 6) nach unten und ziehen Sie gleichzeitig an der Arretierung (Pos. 8) (Abbildung 7). Das flexible Drahtseil klappt nach oben und die Spannzangen öffnen sich.
Sicherheitsstift (Pos. 5) am Adapter einfahren kann und die Betätigung nicht mehr blockiert ist (Abbildung 11). Abbildung 11 Abschließen eines TW57 mit Bügelbetätigung und Betätigungshebel Î Führen Sie die Betätigung (Pos. 1) bis zum Anschlag nach oben (Abbildung 12). Die Spannzangen öffnen sich.
Seite 50
Betriebsanleitung Abschließen eines TW57 mit Betätigungsbügel, flexiblem Drahtseil und Arretierung Î Klappen Sie die Betätigungsbügel (Pos. 6) nach unten und ziehen Sie gleichzeitig an der Arretierung (Pos. 8) (Abbildung 14). Das flexible Drahtseil klappt nach oben und die Spannzangen öffnen sich.
Überprüfen Sie das WEH Produkt nach den Wartungsarbeiten auf Leckage. Beachten ® Sie hierzu das Kapitel 7. Installieren auf Seite 44. - Zum Zweck der Inspektion ist es nicht notwendig, dass das WEH Produkt abgebaut ® wird, es muss allerdings drucklos sein.
® Inspektion – umgehend zur Wartung an WEH. Sollten Sie das WEH Produkt nicht ® regelmäßig inspizieren und zur Wartung an WEH schicken, kann es insbesondere zu Undichtigkeiten und damit unter Umständen auch zu Ausfällen und/oder Unfällen kommen. Seite 52...
Kapitel 3. Produktübersicht / Produktbeschreibung auf Seite 38. Î Tauschen Sie das WEH Produkt aus oder schicken Sie es zur Wartung an WEH ein, ® falls Sie Undichtigkeiten oder Fehlfunktionen feststellen. Das Produkt darf nicht mehr verwendet werden.
Seite 55
Betriebsanleitung 9�4�1 Austausch der Frontdichtung (Pos� 7) Î Stellen Sie den WEH Adapter ® senkrecht auf und klappen Sie die Betätigung um, sodass der Adapter im anschlussbe- reiten Zustand ist. Î Untergraben Sie die Frontdich- tung (Pos. 7) mit dem O-Ring-Picker ®...
Kapitel 3. Produktübersicht / Produktbeschreibung auf Seite 38. 10�1 Sicherheitshinweise zum Schmieren Î Achten Sie darauf, dass Sie keine Dichtflächen/Dichtungskomponenten während des Schmierens beschädigen. Î Verwenden Sie zur Schmierung ausschließlich das WEH Schmiermittel ® Art. Nr. E99-44923. 10�2 Schmieren Î...
Bestellnummer Position Beschreibung Auf Anfrage Pos. 7 Frontdichtung Î Geben Sie bei der Bestellung die auf Ihrem WEH Produkt gekennzeichnete ® Artikelnummer an. Bitte beachten: Beachten Sie zur richtigen Verwendung von WEH Ersatzteilen das ® Kapitel 9. Inspizieren | Warten auf Seite 51.