Technical Data; Before Starting The Equipment - EINHELL GC-CH 18/40 Li Originalbetriebsanleitung

4. Technical data

Rated voltage ..........................................18 V d.c.
Cutter rail length ..................................... 475 mm
Cutting length ......................................... 400 mm
Tooth spacing ........................................... 13 mm
Cuts/min. ..................................................... 2400
Sound pressure level L
Sound power level L
WA
Uncertainty K / K .....................................3dB
pA WA
Sound power level guaranteed L
Vibrations a .........................................≤ 2.5 m/s
h
Uncertainty K ..........................................1.5 m/s
Weight: .......................................................2.0 kg
Caution
The equipment is supplied without batteries and
without a charger. It must only be used with the li-
thium-ion batteries in the Power X-Change series.
The lithium-ion batteries of the Power X-Change
series must only be charged only with the Power
X charger.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
Anl_GC_CH_18_40_Li_SPK13.indb 15 Anl_GC_CH_18_40_Li_SPK13.indb 15
....................... 68 dB(A)
pA
........................... 88 dB(A)
........ 96 dB(A)
WA
2
2
- 15 -
GB
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
Installing the battery pack (Fig. 3)
Press the pushlock button (Fig. 4a/Item C) of the
rechargeable battery and push the rechargeable
battery into the mount provided. Make sure that
the pushlock button engages properly! To remove
the battery, proceed in reverse order!
Charging the battery (Fig. 4)
1. Take the battery pack out of the equipment.
Press the push/lock button to do this.
2. Check that your mains voltage matches the
voltage specifi ed on the rating plate of the
battery charger. Insert the power plug of the
charger into the socket outlet. The green LED
will then begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator"
there is a table with an explanation of the LED
display on the charger.
14.10.2021 13:18:09 14.10.2021 13:18:09