Technical Data; Before Starting The Equipment - EINHELL GE-CH 36/65 Li Originalbetriebsanleitung

4. Technical data

Cutter rail length ..................................... 720 mm
Cutting length ......................................... 650 mm
Tooth spacing ........................................... 30 mm
Cuts/min. ..................................................... 2700
Sound pressure level L
Sound power level L
WA
Sound pressure level at the operator's ear ..........
............................................................... 80 dB(A)
Uncertainty K / K .............................. 3 dB (A)
pA WA
Sound power level guaranteed L
Vibrations a ............................................3.4 m/s
h
Uncertainty K ..........................................1.5 m/s
Caution
The equipment is supplied without batteries and
without a charger. It must only be used with the li-
thium-ion batteries in the Power-X-Change series.
The lithium-ion batteries of the Power-X-Change
series must only be charged only with the Power-
X charger.
The noise generated by the unit can exceed 85
dB (A). The operator will require noise protection
measures if this is the case. The noise emitted by
the hedge trimmer was measured in accordance
with EN 60745-1. The vibration emission level at
the handle was determined in compliance with
EN 60745-1.
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
...................... 73 dB (A)
pA
.......................... 93 dB (A)
........ 96 dB(A)
WA
www.sidirika-nikolaidi.gr
GB
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
2
tion is used.
2

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
Assembly
The hedge trimmer is supplied fully assembled.
All that still needs doing is to slide the cuttings
collector onto the cutter rail if required.
Fitting the cuttings collector (Fig. 4a-4c)
For horizontal cutting we recommend that you
install the cuttings collector. This enables you
to remove the cuttings easily. The surface of the
hedge thus remains clear (Fig. 4a/4b). Position
the cuttings collector (6) on the cutter rail (Figure
4c). Then push the cuttings collector towards the
handle to clamps it securely under the retaining
pin (Fig. 4c/Item A).
Rotatable handle
The hedge trimmer is fi tted with a rotatable rear
handle. It can be rotated 90° to the left and right.
To do this, pull the slide (Fig. 5 / item 5) in the di-
rection of the arrow and rotate the handle.
To return the handle to its original position, pull
the slide (Fig. 5 / item 5) back in the direction of
the arrow. The handle should be rotated through
90° when performing vertical cuts.
Note: The lock cannot be pulled back if the On/
Off switch (Fig. 5/Item 4a) is pressed.
WARNING! Never attempt to move the handle to
a position in between.
Installing the battery (Fig. 6)
Press the push/lock button of the battery pack
- 17 -