Technical Data; Before Starting The Equipment - EINHELL GE-CG 18/1 Li Originalbetriebsanleitung

machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Speed n : ............................................. 1200 rpm
0
Cutting width of the grass cutter: ............ 100 mm
L sound pressure level: ................... 63.4 dB (A)
pA
L sound power level: ...................... 83.4 dB (A)
WA
K uncertainty ...................................... 2.09 dB (A)
Vibration a : ..........................................≤ 2.5 m/s
h
Weight: .....................................................0.66 kg
Sound pressure level
at the operator's ear .............................. 72 dB (A)
K uncertainty ........................................... 3 dB (A)
Important!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
The vibration emission level has been measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
•
The specified emission level can also be
used to make an initial assessment of the ex-
posure to vibrations.
•
The vibration emission level may vary from
the level specified during actual use, depen-
ding on the way in which the power tool is
used.
•
Try to keep the impact from vibrations as low
as possible. Exposure to vibrations can be re-
duced by wearing gloves when using the tool,
for example, and by limiting the amount of
operating time. This includes the full cycle of
operation (e.g. times when the power tool is
switched off and times when the tool is swit-
ched on but no working load is applied).
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
Anl_GE_CG_18-1_Li_SPK7.indb 17 Anl_GE_CG_18-1_Li_SPK7.indb 17
GB
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
2
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
5.1 Charging the battery (Fig. 3-4)
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the mains socket outlet. The green LED
will then begin to flash.
2. Insert the battery pack into the battery char-
ger.
3. In section "Charger indicator" you will find a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
- 17 -
26.04.2021 08:25:31 26.04.2021 08:25:31