Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating Instructions
IR-20 WM Wall Mounted IR Thermometer
Item no: 2347550
1 Intended use
The product is an infrared (IR) thermometer. Use the product to measure surface temperature and count
temperature readings. The product is not designed for medical use.
The product is intended for indoor use only. Do not use it outdoors.
Contact with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to
third parties only together with the operating instructions.
All company names and product names are trademarks of their respective owners. All rights reserved.
2 Delivery contents
■
Product
■
Micro USB cable (1.8 m)
■
2x screws
■
2x wall plugs
■
Double-sided adhesive tape
■
Operating instructions
3 Up-to-date operating instructions
Download the latest operating instructions at
Follow the instructions on the website.
4 Description of symbols
The symbol with the exclamation mark in the triangle is used to indicate important informa-
tion in this document. Always read this information carefully.
5 Safety instructions
Read the operating instructions carefully and especially observe the safety informa-
tion. If you do not follow the safety instructions and information on proper handling in
this manual, we assume no liability for any resulting personal injury or damage to
property. Such cases will invalidate the warranty/guarantee.
5.1 General
■
The product is not a toy. Keep it out of the reach of children and pets.
■
Do not leave packaging material lying around carelessly. This may become dangerous playing mater-
ial for children.
■
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
5.2 Handling
■
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
■
Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
■
Consult an expert when in doubt about the operation, safety or connection of the appliance.
5.3 Operating environment
■
Do not place the product under any mechanical stress.
■
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
■
Protect the product from high humidity and moisture.
■
Protect the product from direct sunlight.
■
Do not switch the product on after it has been taken from a cold to a warm environment. The con-
densation that forms might destroy the product. Allow the product to reach room temperature before
you use it.
■
Never operate the product in direct proximity of strong magnetic or electromagnetic fields or transmit-
ter aerials or HF generators. Doing so can prevent the product from functioning properly.
5.4 LED light
■
Do not look directly into the LED light!
■
Do not look into the beam directly or with optical instruments!
5.5 Li-ion battery
■
Never damage the rechargeable battery. Damaging the casing of the rechargeable battery might
cause an explosion or a fire!
■
Never short-circuit the contacts of the rechargeable battery. Do not throw the battery or the product
into fire. There is a danger of fire and explosion!
■
Charge the rechargeable battery regularly, even if you do are not using the product. Due to the re-
chargeable battery technology being used, you do not need to discharge the rechargeable battery
first.
■
Never charge the rechargeable battery of the product unattended.
■
When charging, place the product on a surface that is not heat-sensitive. It is normal that a certain
amount of heat is generated during charging.
www.conrad.com/downloads
or scan the QR code shown.
6 Overview
6.1 Components
1
2
9
No
Description
1
Tripod thread
2
Micro USB port
3
On/Off switch
4
Surface for adhesive tape
5
Mode button (recessed)
6.2 Operation display statuses
Display shows
Status
_.__
Standby
- - -
Low battery power
7 Placing and mounting
7.1 Finding a suitable location
Finding a suitable location determines the effectiveness and accuracy of the product.
Select a location that is not directly exposed to air-conditioning and cooling fans.
7.2 Mount using the hanging holes
Using the hanging holes and suitable screws you can hang the product on a wall.
If necessary, drill holes and insert wall plugs. WARNING! Risk of electric shock or injury! Before
drilling, check for concealed wires or pipes beneath the surface.
7.3 Mount using adhesive tape
Using double-sided adhesive tape, you can mount the product to a suitable surface.
Important:
You configure the product through the opening at the rear of the product. When using adhesive tape
for mounting, the opening may no longer be accessible.
Before mounting, configure the product and set the desired operating mode.
To mount:
1. Clean the surface on which you intend to mount the product. Make sure it is free of grease and oil.
2. Stick the double-sided tape to the back of the product casing. Make sure not to cover any openings in
the casing.
3. Mount the product to the surface.
7.4 Mount on a tripod
Attach the product to a tripod using the tripod thread.
8 Setting up the power supply
You can power the product via battery or a USB power supply.
8.1 Powering via USB
To power the product via USB, connect a USB power supply (5 V/DC, min. 500 mA) to the micro USB port
on the product.
8.2 (Optional) Setting up the battery power supply
Besides operating the product via a USB power supply, you can install a Li-Ion battery to operate it on
battery power.
If the battery is not supplied, you can purchase one of the type: 1x 3.7 V Li-Ion 18650 (2500 mAh).
8.2.1 Installing the battery
1. Remove the 3 screws from the rear of the casing.
2. Remove the rear part of the casing.
3. Install the battery into the battery compartment. Observe the correct polarity markings.
4. Install the rear part of the casing again.
7
8
No
Description
6
Hanging holes
7
Sensor
8
Indicator lights
9
Display
Required action
Replace the batteries.
3
4
5
6
3
Werbung
Inhaltsverzeichnis
