KIKKA BOO 4 SAFE+ ISOFIX Gebrauchsanweisung Seite 7

Step 3: Install ISOFIX system. Release the ISOFIX system and pull out the head locker to the longest position. Connect the ISOFIX connectors to the vehicle ISOFIX attachments
till the indicator turns from red to green and a click is heard. Then push the seat against the vehicle seat back until tight.
ATTENTION:Please check both sides if ISOFIX telescope is on GREEN color. Please push or pull the car seat if the indicator is red color. To remove and uninstall the seat remove
the top tether, then pull the red ISOFIX handle at the front of the seat and pull the seat forward.
Press on the red button on each side of connector to release from the vehicle ISOFIX anchorages.
Step 4: Install the top tether. The top tether is located at the top of the seat back. Extend the length by squeezing the tension indicating adjuster. Locate the vehicle
attachment point which may be found on the parcel shelf, back of the seat or the rear trunk area and hook on. Tighten the tether strap until the adjuster indicator shows
green.
7. UNSTALL FOR GROUP 0+ : ONLY VEHICLE BELT
For Group 0+(from birth to 13KGS, from birth to 13 months), the baby car seat should be installed rearward-facing nd use the 5-point safety belt to x the child.
Pull th lap and diagonal section of the vehicle seat belt until fully extended and place the lap part through the base hook ( from top to bottom) from one side and through
the hook (from bottom to top) on the other side and then fasten the vehicle belt. Make sure that the lap belt is under the base. At the same time place the diagonal belt into
the headrest guider. Tighten the vehicle seat belt by pulling rst the lap section then the diagonal part along the direction. Make sure there is no twist in the vehicle belt.
Place your child in the child car seat, make sure that the shoulder strap at the right height of your child.
ATTENTION: Always use full reclined position for Group 0+; When the child is over 13KGS, please use this child seat forward-facing.
8. INSTALLING FOR FORWARD-FACING GROUP I: ISOFIX+VEHICLE BELT
For Group I （9-18KGS, 9 months to 4 years old), this child seat should be installed forward-facing, using vehicle belt to t the child seat and 5 point safety belt to x the child.
ATTENTION: ISOFIX system is optional for Group I.
Install ISOFIX system. Release the ISOFIX system and pull out the head locker to the longest position.
Connect the ISOFIX connectors to the vehicle ISOFIX attachments till the indicator turns from red to green and a click is heard. Then push the seat against the vehicle seat back
until tight.
Turn the child seat to the middle reclined position. Please check the red mark on the base of child seat.
Step 1:Turn the ISOFIX system to the back side of child seat, pull the red locker and lock the ISOFIX system.
Step 2: Release the buckle and take out the cushion(for child over 13KGS, there is no need for a cushion). Place the child seat rmly against the back of forward-facing vehicle
seat.
Step 3: Pull th lap and the diagonal section of the vehicle seat belt until fully extended, place the diagonal part of vehicle seat belt through the headrest guider while placing
the lap belt through the groove marked red. Put 2 parts(diagonal and the lap) on the back of pad passing one side to the other side.
Step 4: Tighten the vehicle seat belt by pulling rst the lap section then the diagonal part along the direction . Make sure there is no twist in the vehicle belt.
For Group I, always use recline position 1 and 2.
9. INSTALLING FOR GROUP II, III: ISOFIX+VEHICLE BELT
For Group II, III (15-36KGS, 3 years old -12 yeas old), this child seat should be installed forward-facing, using vehicle belt to x the child and the child seat.
Attention: Always use up-right position for Group II, III. Attention: ISOFIX system is optional for Group II,III.
Step 1: Install ISOFIX system.
Release the ISOFIX system and pull out the head locker to the longest position.
Connect the ISOFIX connectors to the vehicle ISOFIX attachments till the indicator turns from red to green and a click is heard. Then push the seat against the vehicle
seat back until tight.
ATTENTION:Please check both sides if ISOFIX telescope is on GREEN color. Please push or pull the car seat if the indicator is red color.
Step 2: Place your child in the child seat, make sure that your child`s back is at against the back of child seat. Pull out of the 3-point vehicle seat belt and place the diagonal
belt goes through the headrest guilder while lap belt through the headrest
gider while lap belt through the groove marked red. Make sure both diagonal and lap parts go though the groove marked red on the other side before fasten the vehicle belt.
Step 3: Tighten the vehicle belt by pulling rst the lap section then the diagonal part along the direction. Make sure there is no twist in the vehicle belt.
CLEANING AND MAINTENANCE
These instructions are important. Read them carefully and keep for future reference.
Remove the harness system. Remove the seat cover. To replace the cover, keep the product.
IMPORTANT: The seat cover is a safety feature. Do not use the safety seat without its cover. Do not put the child' s safety at risk by using a di erent replacement cover that has
not been approved, as this would reduce the level of protection o ered by the seat.
CARE INSTRUCTIONS: The cover is removable and washable at 30 °C. Line dry only. Machine wash, cold. Do not bleach. Do not iron. Dryclean, any solvent except Trichlorethyl-
ene. Do not tumble dry. If in doubt, consult either the child restraint system manufacturer or the retailer.
10. LAP AND DIAGONAL BELT: CORRECT FITTING READY
10. LAP BELT: INCORRECT FITTING/NOT READY
11. DO NOT USE THE SAFETY SEAT ON THE FRONT PASSENGER SEAT IF IT IS FITTED WITH AN ACTIVR AIRBAG "SUITABLE ONLY FOR VEHICLES EQUIPPED WITH 3-POINT SEAT BELT,
APPROVED UNDER UN/ECE REGULATION NO. 16 OR OTHER EQUIVALENT STANDART"
ENGLISH