Technical Data; Before Starting The Equipment - EINHELL GE-CL 36 Li E Originalbetriebsanleitung

4. Technical data

Idling speed n ........................ 8,000-13,000 rpm
0
Air speed ................................................ 210 kph
Suction power ....................................... 720 m
Volume of catch bag .................. approx. 45 liters
Sound volume level L
WA
Uncertainty K .............................................. 3 dB
Sound pressure level L
Vibration ahv ....................................... 2.354 m/s
Uncertainty K ..........................................1.5 m/s
Weight ........................................................3.3 kg
Important!
The equipment is supplied without batteries and
without a charger is allowed to be used only with
the lithium-ion batteries of the Power-X-Change
series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Anl_GE_CL_36_Li_E_Solo_SPK13.indb 17 Anl_GE_CL_36_Li_E_Solo_SPK13.indb 17
/h
3
.................... 92.68 dB(A)
.................... 83.1 dB(A)
pA
2
2
- 17 -
GB

5. Before starting the equipment

The equipment is supplied without batteries
and without a charger.
Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1. Mounting the suction tube (Fig. 3a-3g)
•
Plug together the front and rear suction tube
(Fig. 3a) and secure with the screw (Fig. 3b/
Item 12).
•
Now slide the complete suction tube into the
motor housing (Fig. 3c) and secure with the
screws (Fig. 3d/Item 12 / 3e/sItem 13).
•
Fit the two wheels (Fig. 3e/Item 9) into the
wheel support (Fig. 3f/ Item 11). Make sure
that there is an audible click when they en-
gage.
•
Slide the wheel support (Fig. 3g/Item 11) onto
the front suction tube as far as the stop (Fig.
3g/Item D) and secure with the screw (Fig.
3g/ Item 13).
Note: Please note that the two vacuum tubes
must always be joined together before they
are mounted on the motor housing, and that
they must never be taken apart when moun-
ted!
5.2. Mounting the catch bag (Figs. 4-5)
Hang the hook on the suction tube (Fig. 4A) and
on the housing (Fig. 4b). Then slip the catch bag
over the socket on the motor housing; it engages
correctly when it makes an audible click (Fig. 5).
5.3. Fitting the handle
Slide the handle (Fig. 6a/Item A) onto the mounts
in the housing as far as the stop. Then fasten the
handle on both sides with one screw on each side
(Fig. 6b/Item 13).
5.4. Fitting the additional handle
Remove the star screw (Fig. 7/Item B), fi t the
handle (Fig. 7/Item 3) to the mount and secure the
handle in the required position with the star screw.
5.5. Fitting the harness
Open the knurled screw (Fig. 8/Item C), feed the
belt strap (Fig. 8/Item 4) through the opening and
close the knurled screw again.
06.10.2021 10:14:37 06.10.2021 10:14:37